Barco R9001390 - Manual (Page 49)

Service Mode
10-3 5975938 BARCOREALITY 9200TCR+ 020798
R G B V R G B H / C V
On
98 27910
R G B H / C V H
9,'(2,1387
9,'(2 69,'(2
RS 232 IN REMOTE
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY COMMUNICATION PORT
(800-PERIPHERALS) RS232 OUT
IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS CODE IR-RECEIVER
0 I T h is d e v ic e c o m p l ie s w it h P a r t 1 5 o f th e F C C r u le s . O p e r a t io n is s u b je c t t o fo llo w i n g t w o c o n d i ti o n s : ( 1 ) T h is d e v ic e m a y n o t c a u s e h a r m fu l i n te rf e r e n c e ( 2 ) T h is d e v ic e m u s t a c c e p t a n y in te r f e r e n c e r e c e iv e d in c l u d in g in t e r fe r e n c e t h a t m a y c a u s e u n d e s i re d o p e r a t io n
R G B V R G B H / C V
On 9 8 279
10 R G B H / C V H
9,'(2,1387
9,'(2 69,'(2
RS 232 IN REMOTE
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY COMMUNICATION PORT
(800-PERIPHERALS) RS 232 OUT
IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
ГГ!"ГW
ГГ(ГГГГГ#Г6
Г%ГГГГ$ГC“
0 I T h is d e vi c e c o m p l ie s w i th P a r t 1 5 o f t h e F C C r u le s . O p e r a t io n is s u b je c t t o fo l lo w in g t w o co n d it io n s : ( 1 ) T h is d e v ic e m a y n o t ca u se h a rm f u l in t e r fe r e n ce ( 2 ) T h is d e v ic e m u s t a c ce p t a n y in t e r fe r e n c e r e c e iv e d in cl u d in g in t e r fe r e n ce t h a t m a y c a u se u n d e s ir e d o p e r a t io n
Select with or
then <ENTER>
<EXIT> to return.
Change Password
This item is password protected when the password strap is
installed.
How to enable or disable the password function ?
The password function is enabled when the password strap on the
controller module is installed.
To get access to the controller module, proceed as follows :
- Power down the projector and disconnect the power cord from the
wall outlet.
- Turn both lock screws on the side of the front top cover with a
screwdriver or coin counter clockwise.
- Lift up and pivot the top cover. Attention : the cover is not secured
with an incorporated support. When opening, turn it over slowly
and lay it down on the second part of the top cover.
Loosen the locking
screws.
Open the top cover
When the strap is on leg 2-3 or no strap is mounted, the password
function is enabled, when the strap is on leg 1-2, the password
function is disabled.
Password enabled
strap on leg 2-3
Password disabled
strap on leg 1-2
How to change the password ?
Highlight Change password by pushing the control disc up or down
and press ENTER to display the Change Password menu.
ENTER displays the Change Password menu
EXIT returns to the adjustment selection menu.
ADJUST returns to operational mode.
The old password is displayed and can be changed by entering the
digit with the numeric keys of the RCU or local keypad.
Press ENTER to save the new entered password.
Press EXIT if no changes have to be made.
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
CHANGE BAUDRATE PC
RESET LAMP RUNTIME
LAMP RUNTINE HISTORY
LAMP DRIVE MODE
MORE...
CHANGE PASSWORD
Enter new password
0000
Select with or
then <ENTER>
<EXIT> to return.