MK Diamond CX-3 - Manual (Page 10)

10
OPERATION & SAFETY DECALS
DO NOT operate
this equipment
before reading
the owners’
manual!
WARNING !
(A)
WARNING
Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in
their composition may give off dust or mists containing crystalline silica. Silica is a basic
component of sand, quartz, brick clay, granite and numerous other minerals and rocks.
Repeated and/or substantial inhalation of airborne crystalline silica can cause serious
or fatal respiratory diseases, including silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a substance known to cause cancer.
!
(B)
CAUTION
DO NOT
operate without
guards in place.
!
(C)
(3 of them)
WARNING
In the event of
blade failure,
replace blade
guard
immediately.
!
(D)
DANGER
The exhaust from this product
contains chemicals known to
the State of California to cause
cancer, birth defects or other
reproductive harm.
!
(E)
DANGER
Lethal exhaust
gases. Use only
in well ventilated
areas. DO NOT
use indoors.
(F)
WARNING
When refueling
stop engine and
allow to cool.
DO NOT overfill
tank.
!
(G)
CAUTION
DO NOT
touch hot
surface.
!
(H)
CAUTION
Accidental start hazard.
Disconnect spark plug
prior to servicing.
!
(I)
SERVICE OR
WARRANTY
FOR INFORMATION ON
PLEASE CALL
1-800-474-5594
(J)
(K)
CAUTION
Keep
hands and
feet clear.
!
(L)
(M)
WARNING
Handle bar NOT a lifting point.
!
NOTICE
Overtensioning of belts
will result in premature
crank and/or bearing failure.
!
Concrete Saw Warning Label Sheet Part# 166009
Location Description
A Motor Plate Read Manual
B Arm Proposition 65, Dust Warning
C Shaft Cover & Belt Guard Guards in Place
D Blade Guard Replace Blade Guard
E Gas Tank/Side Exhaust/Cancer
F Gas Tank/Top Lethal Exhaust
G Gas Tank/Top Refueling
H Gas Tank/Top Belt Guard Hot Surface
I Gas Tank/Side Accidental Start
J Frame/Back Service
K Frame/Front Hand & Feet Clear
L Handle Lifting Point
M Belt Guard Overtensioning Belts
N Console Machinery Hazard
CX-3
®
SAFETY
J
N
B
L
A
C
M
I
F
G
H
E
C
K
D
The CX-3 ® Concrete Saw is equipped with a number of safety decals. These decals are provided for
operator safety and maintenance information. Should any of these operation or safety decals become
unreadable, replacements can be obtained by calling (800) 262-1575.
Read entire operatorʼs manual before operating this machine. Understand all warnings, instructions and controls. IF YOU DO NOT HAVE AN OPERATORʼS MANUAL, CALL TOLL FREE 1-800-474-5594
Machinery Hazard - Always keep all guards in place and in good condition. Always keep all parts of your body away from blade and all other moving parts. Never allow blade exposure to exceed 180°.
Always use blades with a rated speed above the blade shaft speed. Excessive speed can cause blade
breakage. Verify speed by checking blade shaft RPM, pulley diameters and blade flange diameter.
Never use damaged blades or equipment.
Never operate this machine in areas of combustible material.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints • Crystalline silica from bricks and cement and other masonry products • Arsenic and chromium from chemically-treated lumber
Always wear safety approved hearing, eye, head and respiratory protection
WARNING
(N)