Rockwell Automation 1336T FORCE to PowerFlex 700S Phase II Drive Conversion Guide - Manual (Page 34)

1336 FORCE™ To PowerFlex® 700S Phase II AC Drive Conversion Guide
34
Cable Recommendations - Control
Table G Recommended Control Wire
Type Wire Type(s) Description
Insulation
Rating
Digital I/O Un-shielded Per US NEC or applicable national or local code – 300V, 60 o C
(140 o F),
Minimum
Shielded Multi-conductor shielded cable such as Belden
8770(or equiv.) 0.750 mm 2 (18AWG), 3 conductor,
shielded.
Standard Analog I/O Belden 8760/9460(or equiv.) 0.750 mm 2 (18AWG), twisted pair,
100% shield with drain (5) .
(5) If the wires are short and contained within a cabinet which has no sensitive circuits, the use of shielded wire may not be necessary, but is always
recommended.
300V,
75-90
º C
(167-194 º F) Remote Pot Belden 8770(or equiv.) 0.750 mm 2 (18AWG), 3 cond., shielded
Encoder/Pulse I/O
Less 30.5 m (100 ft.) Combined: Belden 9730 (or equivalent) (1)
(1) Belden 9730 is 3 individually shielded pairs (2 channel plus power). If 3 channel is required, use Belden 9728 (or equivalent).
0.196 mm 2 (24AWG), individually
shielded.
Encoder/Pulse I/O
30.5 m (100 ft.) to 152.4 m
(500 ft.) Signal: Belden 9730/9728 (or equivalent) (1) 0.196 mm 2 (24AWG), individually
shielded.
Power: Belden 8790 (2)
(2) Belden 8790 is 1 shielded pair.
0.750 mm 2 (18AWG)
Combined: Belden 9892 (3)
(3) Belden 9892 is 3 individually shielded pairs (3 channel), 0.33 mm 2 (22 AWG) plus 1 shielded pair 0.5 mm 2 (20 AWG) for power.
0.330 mm 2 or 0.500 mm 2 (3)
Encoder/Pulse I/O
152.4 m (500 ft.) to 259.1 m
(850 ft.) Signal: Belden 9730/9728 (or equivalent) (1) 0.196 mm 2 (24AWG), individually
shielded.
Power: Belden 8790 (2) 0.750 mm 2 (18AWG)
Combined: Belden 9773/9774 (or equivalent) (4)
(4) Belden 9773 is 3 individually shielded pairs (2 channel plus power). If 3 channel is required, use Belden 9774 (or equivalent).
0.750 mm 2 (18AWG), individually
shielded pair.
Stegmann Encoder Stegmann 6-411682-xx cables with C12 FUR connections
Resolver Paige 412081 (or equiv.) Twist, capacitance, inductance and resistance
specifications equal to or greater than cable specified 0.750 =mm 2 (18 AWG), twisted pair 300V, 80 o C (176 o
F) minimum
SynchLink Versalink V-System, Lucent Technologies, Specialty Fibers Technology
Division 1403-CF BLK 200/230 micron HCS (Hard Clad Silica)
650 nm (Red) Data Rate 5 Mbps
EMC Compliance Refer to position “i” - Emission of the Catalog Number Explanation on Page 11 for details.