Reloop RMX-80 DIGITAL - Manual (Page 17)

17
ENGLISH
2.8 fader-Start / CrOSSfader-Start
If you have connected appropriate CD players to the RMX-80 Digital (as described under Connections, item 1.6), you can trigger these via the
Crossfader -9- or Linefader -7-, respectively.
To do so, activate the Fader-Start Switch -13- or the Crossfader-Start Switch -11-, respectively.
Crossfader-Start:
If you move the crossfader all the way to the left, the CD player connected to Fader- Start Port “A” will switch to playback mode and the CD player
connected to Fader-Start Port “B” will return to the last saved cue point and switch to pause mode.
If you move the crossfader all the way to the right, the CD player connected to Fader-Start Port “B” will switch to playback mode and CD player
connected to Fader-Start Port “A” will return to the last saved cue point and switch to pause mode.
Fader-Start:
If you close the fader, the CD player connected to the respective channel via fader-start will return to the last saved cue point and switch to pause mode.
If you open the fader, the CD player will switch to playback mode.
NOTE! Please also refer to the information regarding fader-start of your CD player‘s instruction manual. Depending on the CD player model,
deviations from the above described functionalities may be possible.
2.9 dJ MIC
By using the Mic Switch -20- you can activate the microphone and, as the case may be, the talkover effect. This means the suppression of the
remaining channels via the microphone signal (Active Ducking Technology).
In the OFF position the channel is turned off. ON activates the microphone‘s signal, TALKOVER activates the talkover function (Active Ducking
Technology).
Under item `Setup Utility 5.2.4 TALKOVER´ you can find further information and setting options.
2.10 MOnItOrIng
With the Cue Buttons -6- you can select the input channel(s) that you wish to monitor via your headphones.
With Cue Mix -23- you can fade between the channel(s) selected via the Cue Buttons and the master signal. In the CUE position you will only hear
the monitoring channels selected via the Cue Buttons; in MASTER position you will only hear the master signal.
You can mix the signals steplessly. This way you can simulate a mix via your headphones. With the Headphones Input Volume Dial -24- you can
adjust your headphones‘ volume level. With the Headphones Equalizer -22- you can adjust the headphones signal‘s acoustic pattern steplessly.
In the LOW position the low frequencies will be emphasized, in the HIGH position the high frequencies will be emphasized. Via the Mono/Stereo
Switch -21- you can select the headphones channel‘s output mode.
Under item `Setup Utility 5.2.3 CUE SET´ you can find further information and setting options.
2.11 MaSter SeCtIOn
By using the master dial you can adjust the master output volume.
Make sure that the Master Signal‘s LED -26- is only visible in the yellow range.
Via the Master Balance Dial -28- it is possible to select the relation of the right and left output volume level. In the middle position the volume of
the two channels is equal.
Adjust the booth output volume via the Booth volume Dial -29-.
Via the Mono/Stereo Switch -27- you can select the booth output‘s output mode.
NOTE! The rec Output -52- is not affected by the Volume Dials‘ -25, 29- position.
Under item `Setup Utility 5.2.1 MASTER´ you can find further information and setting options.
3. effeCt UnIt
3.1 OVErVIEw
The RMX-80 Digital disposes of the following high-quality DSP effects with studio quality:
Flanger, delay, echo, reverb, transformer, pitch shift, loop roll, reverse loop, noise, bit crusher, gate, tape delay, send/return.
Extensive information and parameters are shown on the Display -37-.
3.2 EFFECT SElECT, rOUTINg
The selection and routing of an effect always follow the same principle.
In the Effect Display -38- the effect names are shown.
By turning the BeatFX Encoder -30- you can select the effects.
Blinking effect names signalize that the respective effect is selected but not yet active.
If you press the BeatFX Encoder -30-, the currently selected effect will be activated.
The active effect‘s name will now stop blinking -38-.
By using the FX Channel Select Switch -31-, the active effect can be assigned to any desired channel (1, 2, 3, 4, Mic, XFA, XFB, Master).
The FX Channel Display -39- shows the selected channel as red framed icon.
If you have activated the desired effect and assigned it to the desired channel, you can turn the effect unit on or off via the Effect ON/OFF Button
-36-. If the effect unit is turned on, the button will shine yellow.
Now you can add the effect to the original source signal via the Level/Depth Dial -35-.
Some effect parameters can be manipulated via the Time Encoder -32- or the Time Bar Buttons -33-, respectively. If a Time Bar Button is pressed,
the corresponding button will be lit.
If the time parameter does not correspond exactly to the specified bar lengths, the two bar values that are between the value will blink.
The value adjusted via the Time Encoder -32- or Time Bar Buttons -33- will be shown as bar/milliseconds for tempo-based effects in the Time/
Length Display. Moreover the Time Bar Buttons‘ position will be shown as graphic above the values.
If you manipulate a value that has been adjusted via the Time Bar Button with the Time Encoder, the Time Bar Buttons‘ position will follow the
current value.
For details regarding the effects, please refer to the following description.