Sony STR-D711 User Manual
Fm stemo/fm-am receiver
Advertising
Table of contents
Document Outline
- FM Stemo/FM-AM Receiver
- Warning
- Precautions
- Unpacking
- To prevent internal heat buildup in the unit,
- Do not install the unit:
- Do not place anything on top of the cabinet.
- Do not throw away the carton and packing material!
- To avoid damage caused by battery leakage and corrosion
- Battery life
- For areas with difficuit AM reception
- On the IMPEDANCE selector (STR-D911 only)
- Note
- Note
- Caution
- Identifying the Parts and Controls
- Operating with the Remote Commander
- Selecting a Program Source
- To adjust volume
- To reduce the sound to a low level temporarily (- 20 dB attenuation)
- IMPORTANT
- Press TUNER.
- Select FM or AM.
- Press DIRECT.
- 4 Enter the frequency.
- To correct the entered frequency
- For entering AM frequencies
- If you enter a frequency not covered by the tuning Interval
- When the entered frequency does not exist in the receivable frequency range
- When an FM stereo program is noisy
- 2 Tune in the desired station.
- Press MEMORY.
- 4 While MEMORY appears, select the memory page (A, B or C).
- Replacing a preset station
- Press TUNER.
- Select the memory page (A, B, or C).
- Designate the desired preset station number with the numeric buttons.
- IMPORTANT
- Press TUNER.
- Tune in the desired station with Preset Tuning.
- 3 Press CURSOR MODE to seiect the iNDEX mode.
- Create an index name.
- If you store an already categorized station under any other index name
- To display the frequency and index name of preset stations
- Press DISPLAY to set to the index mode.
- Select the desired station.
- 1 Select VIDE01, VIDEO 2fLD or VIDEO 3 (STR- D911 only).
- Turn on the monitor TV.
- Select the desired program on the TV tuner or №eVCR.
- Select TUNER and tune in the FM simulcast TV program on the receiver.
- Recording an Audio Source
- Note on recording
- Monitoring the recorded sound
- 1 insert the recorded tape into tape deck 1 (or the DAT deck).
- 2 insert a blank tape into tape deck 2 and adjust the recording level.
- Press TAPE 1 or DAT to select the deck for playback.
- With the STR-D911
- Press VIDEO 2/LD or VIDEO 3 to select the video signai to monitor on the monitor TV according to the VCR to be piayed.
- Set the VCR 1 in the recording mode.
- 4 Set the piayback VCR in the piayback mode.
- To iisten to an audio program during video tape dubbing
- With the STR-D711
- Set the VCR 1 in the recording mode.
- Set VCR 2 in the playback mode.
- To listen to an audio program during video tape dubbing
- To record a TV program
- — Video editing —
- To switch the playback VCR during dubbing
- To view the other video source(s) on the monitor TV during dubbing
- With the STR-0911
- Select the playback VCR with EDIT VIDEO.
- Set the playback VCR to the playback mode.
- 3 At the point where audio dubbing starts, press the pause button on the playback VCR.
- Press EDIT AUDIO.
- Select the audio program source with the function selectors.
- G Set VCR 1 in the recording mode and then release the pause mode of VCR 2.
- Start playback of the selected audio program source.
- 1
- ^ Chpater 3 Advanced Operations
- PHANTOM mode
- WIDE mode
- 5 Press CURSOR MODE.
- To adjust the level of center speakers
- To adjust the level of rear speakers
- Press T. TONE on the remote commander to set to off.
- Sequence of the test tone
- Press SOUND FIELD ON/OFF to ON.
- 2 Press DOLBY SUR.
- Select the Dolby pro logic mode with the PRO LOGIC button according to your speaker system.
- Press T. TONE on the remote commander to set toon.
- — for DOLBY SUR (Dolby surround) mode
- 1 Press DOLBY SUR.
- 2 Press CURSOR MODE.
- Press A or V to select the delay time mode.
- Press < or > to adjust the delay time.
- Press the desired SOUND FIELD program.
- 2 Press CURSOR MODE.
- Press A or V to select the desired parameter.
- Press < or > to adjust the parameter.
- To turn off the surround effect
- Note
- Sound Field Settings
- ound Field Settings
- 1
- 1
- Press the desired SOUND FIELD program.
- 3 Press CURSOR MODE.
- 4 Press A or V to select the mode you want to adjust.
- S Press < or > to adjust the level or delay time.
- When you store a new SOUND FIELD effect
- Even if AC power cord Is disconnected
- When selecting ACOUSTIC
- Restoring to the setting stored at the factory
- Press SOUND FiELD LiNK ON/OFF to ON.
- Press the desired SOUND FiELD program.
- Notes
- Troubleshooting Guide
- Specifications
- Quick Reference
- r^,