Cuddeback C3000 - Manual (Page 5)

Longer Battery Life Faster Trigger Time
Page 4 of 20
i) Attach a TV or camcorder to the TV connector on the Cuddeback. See the section TV Requirements for more
information about using a TV with your Cuddeback.
ii) When [Images Saved] is on the display press the (UP KEY) or (DOWN KEY) to view the images. [DO NOT
REMOVE CARD] will appear on line 2 of the LCD display.
iii) Continue to view images by pressing the (UP KEY) or (DOWN KEY).
iv) Press the (M KEY) to redisplay the number of images saved on the memo ry card.
b) CLEAR the IMAGE displayed on the TV:
i) Press the (C KEY). The LCD will prompt [Clear Image?] on line 1, and [C = Yes] on line 2.
ii) To clear the image press the (C KEY) a second time. To continue without clearing the image, press the (UP KEY) ,
(DOWN KEY), or (M KEY).
c) TO ERASE ALL IMAGES:
i) When [Images Saved] is on the display you can clear all images on the memory card. If [Images Saved] is not
on the display, press the (M KEY) until it is.
ii) Press the (C KEY). The LCD will prompt [Clear All Images?] on line 1, and [C = Yes] on line 2.
iii) Press the (C KEY) a second time. To continue without clearing the images, press the (UP KEY) , (DOWN KEY) or
(M KEY).
iv) To prevent accidentally clearing all the images you will be required to enter a password before all t he images will be
cleared.
(1) The LCD will promp t [Enter LPW to Clear All Images] on line 1, and [<0---->] on line 2.
(2) The default password in E-Z Mode is 0 -0-0-0-0. This is entered by pressing the (UP KEY) four times (you can
change this password in Advanced Mode).
(3) After the five 0s are entered press the (C KEY) to clear all images.
(4) If you do not want to clear all the images press the (M KEY) during any of the above steps.
3) Operating Mode –Using the operating mode you can arm, disarm, and test Cuddeback’s mo tion/heat sensor.
a) Press the (M KEY) until [Standby] appears on the LCD display.
b) Press the (UP KEY) or (DOWN KEY) to change the operating mode. There are four selections available:
c) Standby – Cuddeback will not trigger the camera. This state is used when you are programming and viewing images .
Cuddeback will automatically activate Live Camera mode if left in the Standby Mode.
d) Test Mode – Cuddeback is in test and align mode where the LED will illuminate when activity is sensed. This is useful to
verify Cuddeback’s detection zone and to assist in aligning Cuddeback to trigger where you desire. Cuddeback will
automatically activate Live Camera mode if left in Test Mode.
e) Live Mode – Cuddeback will trigger the camera when activity is sensed. When Live Camera mode is initiated there will be a
45 second delay before the motion sensor starts . This provides you with enough time to replace the battery cover and move
away from the camera. The LCD display will clear when the motion sensor activates.
f) Cuddeback Disarmed – Cuddeback is off and will not trigger the camera. This mode is useful for transporting the
Cuddeback without having Cuddeback trigger the camera. Before disarming the LCD will prompt [C to Disarm]. You
must press the (C KEY) to disarm the Cuddeback. The Cuddeback will then prompt [Disarmed]. To rearm Cuddeback
press you press the (UP KEY) or (DOWN KEY) to change the operating mode to Standby, Test, or Live Camera as desired.
g) If you press the (M KEY) or (S KEY) during any of the above displays, Cuddeback will remain in the operating mode
displayed.
h) Automatic Operation. To prevent Cuddeback from being left in the field in the wrong mode Cuddeback features automatic
operation. About ten minutes after your last key press Cuddeback will automatically activate Live Camera mode. This
automatic operation is disabled when Cuddeback is disarmed.
STEP 4 – Attaching Cuddeback to a tree
We recommend mounting Cuddeback to the largest tree in the area, about 10 feet from where you expect the animal to appear. Place
Cuddeback about 3 to 4 feet off the ground, aiming slightly down. You can use Cuddeback’s Test Mode to verify the detection
distance.
We strongly recommend using the supplied Torx
®
screw to secure Cuddeback to a tree. You will need a #25 Torx screwdriver.
! WE STRONGLY RECOMMEND THAT YOU
ONLY USE THE TORX SCREW SUPPLIED.
!