Panasonic NV-HD 630 - Manual (Page 37)

Before Requesting Service
Before requesting service, check the following points again.
*..'•
'
*K\ ' *' ' Ji
* ' T , '
On screen dispiay
messages are displayed.
The error message is indicated in brackets [ ].
[PLEASE PUT iN A VIDEO CASSETTE.]
m- • REC/OTR (REC •) or TIMER REC Q has been
pressed without a video cassette inserted.
Insert a video cassette with an intact erasure
prevention tab.
[PLEASE STOP THE TAPE.]
m- TUNER PRESET has been selected during
playback. Stop the tape.
[PLEASE SET THE CLOCK.]
<sr TIMER REC Ei. G-CODE or PROG./CHECK has
been pressed when the clock is not set
Set the ciodi.
[PLEASE USE A CASSETTE WITH TAB.]
isr • REC/OTR (REC •) or TIMER REC B has been
pressed without a video cassette with an intact
erasure prevention tab.
Use a video cassette with an intact erasure
prevention tab.
[NO TiMER RECORDiNG HAS BEEN SET.]
1 ^ TIMER REC Ei has been pressed with no timer
programmes.
Set timer recording.
[TIMER PROGRAMMES ARE FULL]
isr G-CODE has been pressed when 8 programmes
have been already set.
Cancel unnecessary programmes.
[VCR IS IN THE TIMER STANDBY MODE.]
^ POWER c!)/l (POWER Cb) has been pressed during
the timer standby mode.
Press TIMER REC El to release the VCR from the
timer standby mode.
[DEW FORMED IN THE VCR.]
w Dew has formed.
Wait until the message disappears.
The symptom description is indicated in quatations “ ".
This VCR has a seif-diagnosis and display function. If the
VCR detects trouble during installation or during use, the
following indications automatically appear in the VCR
display. Indications are in the form of a single English letter
plus two numbers, such as [H01].
INDICATION; U10
CAUSE: Dew has formed.
REMEDY: Wait until the indication disappears.
INDICATION: HDD, FDD
CAUSE: Some trouble has occurred. (Numbers
after H and F differ according to the
status of ttie VCR.)
REMEDY: Consult Panasonic Custmer Care
Centre for advice on 132600. (NV-
HD630Aonly)
The symptom description is indicated in quatations “
'The VCR display is not illuminated."
m~ The mains lead has not been connected.
Connect the mains lead to the VCR.
or Power save setting is ON. Set POWER SAVE to
OFF. (See page 23.)
"ITie VCR display is illuminated but the VCR will not
operate,"
er The VCR is in the timer mode.
Press TIMER REC El to operate the VCR manually,
lar Safety devices are operating.
Disconnect the mains lead and wait for 1 minute.
Reconnect the mains supply and check functions.
m- Dew may have formed.
V\№en the dew indicator flashes, wait until this
indicator disappears.
"An unknown language arrears on the TV screen.”
m- The language setting has been set to an unknown
language.
Select the desired language. See page 17.
, ^ ^ \ - .............. V '
The symptom description is indicated in quatations “ ”.
"The picture is noisy or is not in colour.
Horizontal bars or lines run down the screen."
Q3T Tracking is not correct.
Adjust the tracking. See page 5.
o- The TV has not been tuned to the VCR.
Tune the TV to the VCR. See page 10.
^ The video heads are clogged or worn.
Consult Panasonic Customer Care Centre for advice
on 132600. (NV-HD630Aonly)
■S
3:
5
.Q.
37