Cuisinart BFP-10 Series - Manual (Page 7)

7
to desired consistency. See the Recipe Tips section in recipe
booklet for more details.
9. TO DISLODGE FOOD: Use a rubber or plastic spatula to help
remove food lodged around the cutting assembly. DO NOT
USE SPATULA UNTIL YOU HAVE TURNED THE BLENDER
OFF.
Replace the cover and measured pour lid and continue blending,
if necessary. Make sure spatula is not inside the blender jar before
blending.
10. WHEN FINISHED BLENDING: Press the Off button and
unplug the blender from the electrical outlet. Never remove the
blender jar from the motor base until the blender is off. Do not
twist locking ring from blender jar when removing jar from
motor base. Simply lift blender jar from motor base. Do not
place hands into blender jar with blender plugged in.
CLEANING, CARE AND MAINTENANCE
Always unplug your Cuisinart ® PowerBlend Duet ® from the
electrical outlet before cleaning. The blender is made of corrosion-
resistant parts, which are easy to clean. Before first use and after
every use, clean each part thoroughly. Periodically check all parts
before reassembly. If any part is damaged or blender jar is chipped
or cracked, DO NOT USE BLENDER.
Remove the blender jar from the motor base by lifting straight up
and away. Twist off the locking ring by turning counterclockwise.
Remove the cutting assembly and rubber gasket. Wash in warm
soapy water; rinse and dry thoroughly. Place the locking ring in
the upper rack of the dishwasher or wash in warm water.
CAUTION: Handle the cutting assembly carefully. It is SHARP and
may cause injury. Do not attempt to remove blades from cutting
assembly.
Remove the blender jar cover and the measured pour lid. Wash in
warm, soapy water; rinse and dry thoroughly, or place in the upper
rack of the dishwasher. The blender jar should be washed in warm
soapy water and rinsed and dried thoroughly. The blender jar can
also be placed upside down in the dishwasher.
Finally, wipe the motor base clean with a damp cloth to remove
any residue, and dry thoroughly. Never submerge the motor base
in water or other liquid, or place in the dishwasher.
Tip: You may wish to clean your blender cutting assembly as
follows: Squirt a small amount of dishwashing liquid into
assembled blender jar and fill halfway with warm water. Run on
Stir for 15 seconds. Repeat using clean tap water. Empty blender
jar and carefully disassemble parts. Wash cutting assembly, gasket
and locking ring in warm, soapy water. Rinse and dry all parts
thoroughly.
Any other servicing should be performed by an authorized service
representative.
DO’s AND DON’Ts WHEN USING
YOUR BLENDER
DO:
• Make sure the electrical outlet is rated at the same voltage as
that stated on the bottom of the blender motor base.
• Always use the motor base on a clean, sturdy and dry surface.
• Always add liquid ingredients to the blender jar first, then add
remaining ingredients. This will ensure that ingredients are
uniformly mixed.
• When using either blender or food processor, cut most foods
into cubes approximately ½" to 1" to achieve a more uniform
result. Cut all cheeses into pieces no larger than ½".
• When using blender, use the measured pour lid to measure
liquid ingredients such as alcohol. Replace measured pour lid
after ingredients have been added.
• When using either blender or food processor, use a rubber or
plastic spatula as needed, only when the blender is turned OFF.
Never use metal utensils, as damage may occur to the blender
jar/work bowl or cutting assembly.
• Place blender cover on firmly. Always operate the blender with
the cover on.
• Make sure locking ring is tightly attached to blender jar.
• Always remove locking ring, cutting assembly, and rubber gasket
before cleaning.
• When scraping the blender jar with a spatula, remove the food
from the sides of the blender jar and place it in the center of the
blender jar, over the cutting assembly.