How то mmovt odors, Gy wing ideas, How to remove and replace light bulbs – Kenmore 596.50012100 User Manual

Page 24: A warning, A caution, Upper fresh food, Lower fresh food, Section b, Freezer section, Ice and water dispenser

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

HOW то MMOVt ODORS

1, Remove all food,

2 Disconnect refrigerator,

3, Glean the following items-paying

special attention to crevices-using
the appropriate instructions in How to
Clean Your Refrigerator:

■ Wails, floor, and ceiling of cabinet

interior,

* Drawers, shelves, and gaskets

4 Wash and dry all bottles, containers,

and jars. Discard spoiled or expired
items

5, Wrap or store odor-causing foods ir>

tightly-sealed containers to preverri
reoccurring odors

6 Connect power to refrigerator and

return food.,

7 After 24 hours, check if odor has

been eliminated.

If odor is still present...

1, Remove drawers and place on top

shelf of refrigerator,

2, Pack refrigerator and freezer

sections-including doors-with
crumpled sheets of bfack and white

newspaper.

3 Place charcoal briquettes randomly

on crumpled newspaper in both

freezer and refrigerator
Gompartments.

4, Close doors and let stand 24-48 hours.

5, Repeat steps 5 through 7 above.

If odor was not eliminated, contact

Sears Service Center. Refer to back of
manual for phone number;.

№GY WING IDEAS

> Avoid overcrowding refrigerator

shelves. This reduces effectivity of air
circulation around food and causes
refrigerator to run longer..

>- Avoid addirrg too much warm food to

refrigerator at one time. This
overloads compartments and slows
rate of cooling

>■ DO NOT use aluminum foil, wax paper,

or paper toweling as shelf liners This
decreases air flow and causes
refrigerator to run less efficiently,

> A freezer that is % full runs most

efficiently

>■ Locate refrigerator in coolest part of

room. Avoid areas of direct sunlight,
or near heating ducts, registers, or
other heat producing appliances, if
this is not possible, isolate exterior by
using a section of cabinet or an
added layer of insulation,

> Refer to section in Use and Care

Guide on temperature controls for
recommended control settings

>“ Clean door gaskets every three

months according to use arrd care
guide instructions This will assure
that door seals properly and
refrigerator runs efficiently

>■ Take time to organize stems in

refrigerator to reduce time that door

is open,

> Be sure your doors are closing

securely by leveling refrigerator as

instructed in your use and care guide,

>■ Glean condenser coils off as

indicated in the Use and Care Guide
every 3 months. This wlil increase
energy efficiency and cooling
performance.

HOW TO REMOVE AND

REPLACE LIGHT BULBS

A WARNING

To avoid eiectrica! shock which can

; cause sevère personal irtjury or death,

disconnect power to refrigerator

before replacing light bulb. After

■ replacing light bulb, coririect power.

A CAUTION

To avoid personal injury or property

damage, observe the following:

>■ Aiiow'light bulb to cooi.

>■ Wear gloves when repiacing light

bulb.

UPPER FRESH FOOD

S

ection

[]

1 Locale finger

gaps on each -r

side of clear light

shield- Insert
fingers and press in on each side of
shield. Pull shield down and remove

2 Remove light bulbs

3 Replace with appliance bulbs no

greater than 40 watts.

4 Replace light buib cover by inserting

front tabs of light shield into slots
directly in front of light assembly

LOWER FRESH FOOD

SECTION

B

1. Pinch bottom tabs

(A) on light cover
and pull straight

out

2. Remove light bulb

3 Replace bulb with appliance bulb

no

greater than 40

waffs.

4 Insert top tabs (0) of light cover into

liner slots and snap bottom portion
over light assembly,

FREEZER SECTION

1 Remove ice bin by

lifting front of bin

and pulling out

2 Remove tight bulb

cover by pinching top tab

(A)

and pulling cover out,

3. Remove light bulb Replace with

ai^liance bulb

no greater Own 40

watts.

4. Insert bottom tab (B) of light cover

into liner slots and snap top portion
over light assembly

5 Replace Ice bin by sliding in until bin

locks irrto place

ICE AND WATER
DISPENSER

1 Locate light bulb inside top edge of

dispenser frame, Unscrew to remove.

2 Replace light buib with a

7-watt, 120 volt bulb

24

OTOve.

i

Advertising
This manual is related to the following products: