Emerson Radio iC2196 - Manual (Page 3)

4
CLASS 1 LASER PRODUCT
This product contains a low power Laser Device.
IMPORTANT NOTES
3
Avoid installing this unit in places exposed
to direct sunlight or close to heat radiating
appliances such as electric heaters, on top
of other stereo equipment that radiates too
much heat, places lacking ventilation or
dusty areas, places subject to constant
vibration and/ or humid or moist areas.
Do not attempt to clean this unit with
chemical solvents as this might damage
the finish. Use a clean dry cloth. O p e r a t e c o n t r o l s a n d s w i t c h e s a s
described in the manual.
Before turning ‘On’ the power, make
certain that AC power cord is properly
installed.
Store your CDs in a cool area to avoid
damage from heat.
When moving the set, be sure to first
disconnect the AC power cord.
NOTE: This product complies with DHHS Rule 21 Subchapter J at date of manufacture.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
PREPARATION FOR USE
Unpacking and Set-up
Protect Your Furniture
This model is equipped with non-skid rubber ‘feet’ to prevent the product from moving
when you operate the controls. These ‘feet’ are made from non-migrating rubber
material specially formulated to avoid leaving any marks or stains on your furniture.
However certain types of oil based furniture polishes, wood preservatives,or cleaning
sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on
the furniture. To prevent any damage to your furniture we strongly recommend that
you purchase small self-adhesive felt pads, available at hardware stores and home
improvement centers everywhere, and apply these pads to the bottom of the rubber
‘feet’ before you place the product on fine wooden furniture.
The display carton contains the main unit, five (5) different iPod ® adapters, and one
(1) iPod ® dust cover.Remove all of the components from the carton and make sure
t h a t n o t h i n g i s a c c i d e n t a l l y d i s c a r d e d w i t h t h e p a c k i n g m a t e r i a l s .
We recommend that, if possible, you save the carton and packing materials in the
event that your unit ever needs to be returned for service. Using the original carton
and packing materials is the only way to protect your unit from damage in transit.
Remove all packing materials from the main unit and the accessories.
Remove any descriptive labels from the front or top panels of your unit. Do not
remove any labels from the back or bottom panels.
Remove any small strips of tape that may have been used to secure the CD door
and the secondary control cover door.
Open the CD door. Remove the dummy CD transit protection card from the CD
mechanism.
Remove the “paper dummy iPod ® ” from the docking area.
Unwind the AC power cord and extend it to its full length.
Place the main unit on a stable, level surface such as a table, stand, or shelf,
convenient to an AC outlet, out of direct sunlight, and away from sources of excess
heat, dust, moisture, vibration, and strong magnetic fields.
•
•
•
•
•
•
•
•
2008-1-11, 15:48 3