Interlogix EV1116 - Manual (Page 5)

P/N 146251999-4 (ML) • REV D • ISS 12MAR13 5 / 32
SW 5: Setting LEDs
On: Enables both LEDs on the detector at all times (factory
default).
Off: Puts both LEDs under the control of the Walk Test and
Day/Night input. This activates the memory feature of the
detector.
LED indication
PIR Red LED Alarm relay To reset
Start up Closed Automatically after 25 s
Low voltage Open (Alarm) Apply correct voltage
PIR intruder
alarm Open (Alarm) Automatically after 3 s
PIR/AM Red
LED
Yellow
LED Alarm
relay AM
relay To reset
Start up Closed Closed Automatically
after 60 s
Low voltage Open
(Alarm) Open
(Alarm) Apply correct
voltage
PIR intruder
alarm Open
(Alarm) Automatically
after 3 s
Latched PIR
(Memory) Switch to Night
mode
AM alarm Open*
(Alarm) Open
(Alarm) See DIP
switch 3
After AM reset Switch to
Night mode
Technical fault Open
(Alarm)
Do a successful
walk test
Continuously on Normal blinking (1 Hz)
Fast blinking (4 Hz)
* Depends on the setting of the DIP switch SW4.
Specifications
EV1116 EV1116AM
Detector PIR PIR + AM
Signal processing DSP
Range 16 m
Optical 11 high-density mirror curtains
Memory Yes
Input power
For UL installations 9 to 15 VDC (12 V nominal)
10 to 15 VDC (12 V nominal)
Peak-to-peak ripple 2 V (at 12 VDC)
Detector start-up time 25 s 60 s
Normal current
For UL installations 5.5 mA
0.0528 mW
10 mA
—
Current in Alarm 2.5 mA 3.8 mA
Maximum current
(LED on) 11.5 mA 24 mA
Mounting height 1.8 m to 3.0 m (5.9 ft. to 9.8 ft.)
Target speed range 30 cm/s to 3 m/s
(1 ft./s to 10 ft./s)
20 cm/s to 3 m/s
(0.65 ft./s to
10 ft./s)
Alarm (NC) / Tamper relay
characteristic 80 mA 30 VDC, resistive
EV1116 EV1116AM
Pry-off tamper (not
evaluated by UL/cUL) Optional On-board (Yes)
AM relay characteristic — 80 mA at 30 VDC
max., resistive
PIR alarm time 3 s
Operating temperature
For UL installations −10 to +55°C (14 to 130°F)
0 to 49°C (32 to 120°F)
Dimensions (H x W x D) 125 Ч 55 Ч 60 mm
(4.92 x 2.16 x
2.36 in.)
125 Ч 65 Ч 60 mm
(4.92 x 2.6 x
2.36 in.)
Relative humidity 95% max. noncondencing
(UL Installations)
Weight 150 g
IP/IK rating IP30 IK02
Regulatory information
Manufacturer UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
UL The product must be connected to a listed burglar
system compatible control unit or power supply unit,
which provides a minimum 4 hours of standby power
and has a voltage output between 10 and 15 VDC.
All wiring must be made according to National
Electrical Code, NFPA70, and CSA C22.1, Canadian
Electrical Code Part I, Safety Standards for Electrical
Installations.
Perform walk test at least one per year.
Use only a listed power-limited supply.
EV1116AM has not been evaluated by UL.
FCC Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.