Interlogix IS-ZW-RC-1 - Manual (Page 3)

cams, wireless video devices and older cordless phones using
the 900MHz frequency range may cause interference and
limit Z-Wave functionality. Many 900 MHz products have a
switch to select channel “A” or “B”. You may find that one of
these channels will cause less interference than the other
channel.
Network management
Your remote control and every Z-Wave device you have added
with the primary controller are linked together in a wireless
network. Each device in your network has a unique address
assigned to it and cannot be activated by your neighbor’s Z-Wave
controller.
Add a node, group, or scene can also be referred to as include a
node, group, or scene. Remove a node, group, or scene can also
be referred to as exclude a node, group, or scene.
If the screen displays FAILURE during the setup or programming
process, you have pressed an invalid key or the desired action has
not been successfully completed. Make sure the remote is within
two feet of the device and try again.
Adding a device
In order to control lights, they must be Z-Wave enabled and you
must first add them to your home network. There are two ways to
do this.
• Add lights to your remote so that they can be controlled
individually using the number keys (maximum of 18). Adding a
device to your remote also adds it to your network. If the
device number you are trying to add is already associated
with another device, the previous information is lost.
• Add devices to your home network without assigning them to
a specific number key. These devices can only be controlled
through the Group, Scene, or All commands.
To add a device without assigning it to a specific number key:
1. Press and hold SETUP until the screen shows LIGHT SETUP.
2. Press OK.
The screen displays ADD.
3. Press OK.
The screen displays TO NETWORK.
4. Press OK.
The screen displays SETUP WAITING.
5. Press the button on the device so that it communicates with
the remote.
The screen displays SUCCESS to indicate that the Node/Light
has been successfully added.
You can now add the device to groups and/or scenes.
To add a device and assign it to a specific number key:
1. Press and hold SETUP until the screen displays LIGHT
SETUP
.
2. Press OK.
The screen displays ADD.
3. Press OK.
The screen displays TO NETWORK.
4. Scroll until the screen displays TO A KEY, and then press
OK.
5. Press a digit (1 to 9) for the device location you wish to add.
Press SETUP (SHIFT) and the digit (1 to 9) if you are adding
devices 10 through 18.
6. Press OK.
The screen displays SETUP WAITING.
7. Press the button on the device so that it communicates with
the remote.
The screen displays SUCCESS to indicate that the Node/Light
has been successfully added to the number key and your
network.
Controlling individual lights
You can control a light to turn it on or off, or change its brightness
level. The operation of a specific device varies by product. Refer to
the manual for that device to learn its specific operation.
1. Press and release the LIGHT key to put the remote into
individual light control mode. The remote will stay in this
mode until the Group, Scene, or All mode is activated.
2. Select the lights you want to control. Press and release SHIFT
to control lights 10 to 18.
To turn a light on or off:
• To turn a light on, press and release the ON key for less than
one second. The screen displays the selected light and ON.
• To turn a light off, press and release the OFF key for less than
one second. The screen displays the selected light and OFF.
To set a light’s brightness level:
• To make a light brighter, press and hold the ON key for more
than one second. The screen displays the selected light and
BRIGHT. The light will continue to grow brighter until the key is
released.
• To make a light dimmer, press and hold the OFF key for more
than one seconds. The screen displays the selected light and
DIM. The light will continue to grow dimmer until the key is
released.
To remove a device from your remote:
1. Press and hold SETUP until the screen displays LIGHT
SETUP
.
2. Press OK.
3. Scroll until the screen displays REMOVE, and then press OK.
The screen displays SEL DIGIT.
4. Press a digit (1 to 9) for the device location you wish to
remove. Press SHIFT and the digit (1 to 9) if you are removing
devices 10 through 18.
5. Press OK
P/N 1069507 • REV A • ISS 18NOV09 3 of 8