Interlogix IS-ZW-RC-1 - Manual (Page 7)

The screen displays ADD.
3. Press OK.
The screen displays EVERY DAY.
Use either arrow key to change this option to MON-FRI, SAT-
SUN, ONE TIME, or a specific day of the week.
4. Once you have chosen the event profile, press OK.
The screen displays SEL DIGIT.
5. Press any digit and the screen displays the event number.
6. Press OK and the screen displays ENABLED.
7. Press OK and the screen displays EVENT TYPE.
8. Scroll between the Light, Scene, or Group options (pressing
digits 1 to 9 will adjust the Light number accordingly).
9. After you select the event type, press OK.
The screen displays ON TIME.
Press ON or OFF with the 1 key to adjust the hour.
Press ON or OFF with the 2 key to adjust the minutes.
Press ON or OFF with the 3 key to toggle between AM and PM.
10. Press OK once you have programmed the ON TIME.
The screen displays OFF TIME.
Press ON or OFF with the 1 key to adjust the hour.
Press ON or OFF with the 2 key to adjust the minutes.
Press ON or OFF with the 3 key to toggle between AM and PM.
11. Once you have programmed the off time, press OK.
The screen displays SUCCESS.
Random events
The event feature allows you to program automated events, such
as turning your lights on or off at a predetermined time and day.
By choosing the Random option, the event will start at +/- 15
minutes of the scheduled time.
To activate this function, after step 6 above, use either arrow key
to scroll until the screen displays RANDOM. Press OK and the
screen displays EVENT TYPE. Continue the programming as
shown in step 8 above.
Disabling an event
Once an event has been programmed, you can disable it by
following steps 1 to 6 above and then scrolling to DISABLED and
pressing OK.
To delete an event:
1. Press and hold SETUP until the screen displays LIGHT
SETUP
.
2. Scroll until the screen displays EVENT, and then press OK.
The screen displays ADD.
3. Scroll until the screen displays DELETE, and then press OK
The screen displays SEL DIGIT.
4. Press the digit for the event you want to delete.
5. Press OK.
The screen displays SUCCESS.
To enable all programmed events:
1. Press and hold SETUP until the screen displays LIGHT
SETUP
.
2. Scroll until the screen displays EVENTS, and then press OK.
3. Scroll until the screen displays ALL, and then press OK.
The screen displays ALL ON.
4. Press OK.
The screen displays SUCCESS.
To disable all programmed events:
1. Press and hold SETUP until the screen displays LIGHT
SETUP
.
2. Scroll until the screen displays EVENTS, and then press OK.
3. Scroll until the screen displays ALL, and then press OK.
The screen displays ALL ON.
4. Press either arrow key and the screen displays ALL OFF.
5. Press OK.
The screen displays SUCCESS.
Thermostats
The remote allows you to program and control a Z-Wave enabled
thermostat.
To add a thermostat to the remote control:
1. Press and hold SETUP until the screen displays LIGHT
SETUP
.
2. Scroll until the screen displays THERMOSTAT, and then press
OK.
The screen displays ADD.
3. Press OK.
The screen displays SETUP WAITING.
4. Press the button on the thermostat’s Z-Wave interface.
The screen displays SUCCESS.
Controlling a thermostat
The features and functions that can be controlled vary by
thermostat and you will need to refer to the documentation
provided with the thermostat to determine the capabilities of your
thermostat. If supported by the thermostat, the remote allows you
to check room temperature, adjust HVAC system modes (Heat,
Cool, Fan, and AUTO) and adjust temperature settings (setpoint).
Please note that your HVAC system may have to be set to Heat or
Cool mode in order to remotely check and/or adjust the room
temperature.
P/N 1069507 • REV A • ISS 18NOV09 7 of 8