Sears 113.206930 - Manual (Page 5)

motor specifications and electric€iíf0C|WÍf‘®sTiéfifs
This machine is designed to use a 3450 RPM motor oniv.
Do not use any motor that runs faster than 3450 RPM.
it is wired for operation on f 10-120 volts, 60 H i . , alter­
nating current. IT MUST MOT BE CONVERTED TO
OPERATE ON 230 VOLTS. EVEN THOUGH SOME OF
THE RECOMMENDED MOTORS ARE DUAL VOLTAGE,
THESE CRAFTSMAN MOTORS HAVE BEEN
FOUND TO BE ACCEPTABLE FOR USE ON
THIS TOOL.
HP RPM VOLTS CATALOG NO.
1/2 3450 110-120 1316
1/2 3450 110-120 1218
3/4 3450 110-120 1219
3/4 3450 110-120 1226
CAUTION: Do not use blower or washing machine motors
or any motor with an automatic reset overload protector
as their use may be hazardous.
CONNECTIMG TO POWER SOURCE OUTLET
This machirte must be grounded while
the operator from electric shock. protect
Plug power cord into a 110-120V properiy grounded type
outlet protected by a 15-amp. time delay or Circuit-Saver
fuse or circuit breaker.
If you are not sure that your outlet is properly grounded,
have it checked by a qualified electrician,
WARNING: DO NOT PERiVUT FINGERS TO TOUCH
THE TERMINALS OF PLUGS WHEN INSTALLING OR
REMOVING THE PLUG TO OR FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN INCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED
IN DAMP LOCATIONS IN PROXIMITY TO PLUMBING.
IF AN ELECTRICAL SHOCK OCCURS THERE !S THE
POTENTIAL OF A SECONDARY HAZARD SUCH AS
YOUR HANDS CONTACTING THE CUTTING BLADE.
If power cord is worn or cut, or damaged in any way, have
it replaced immediately.
3-PRONG
This tx)wer tool is equipped with a 3-conductor cord and
groundirrq type plug «Wch has a grounding prong listed by
Undervvnters'
Laboratories Association. Тле ground
conductor has 3 green jacket and is attached to the tool
housimj at one en-d and to the ground prong m the
attachment plug at the other end.
This plug requires
outlet as shown.
mating 3-conductor grounded type
If the outlet you are planning to use for this power tool is
of the two prong type DO NOT REMOVE OR ALTER
THE
grounding prong in ANY MANNER. Use an
adapter as shown and always connect the grounding lug to
known ground.
it is recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong outlet.
An adapter as shown below is available for connecting plugs
tta 2-prong receptacles, The green grounding lug extending
from the adapter must be connected to a permanent ground
such as to a properly grounded outlet box.
MAKE SURE THIS ÍS
CONNECTED TO A
KNOWN GROUND
GROUNDING LUG
ADAPTER
Z-PRONG
RECEPTACLE
3-PRONG
PLUG
I
NOTE; The adapter illustrated is for use only if you already
have a properly grounded 2-prong receptacle.
The use of any extension cord will cause some loss of
power. To keep this to a minimum and to prevent over­
heating and motor burn-out, use the table below to deter­
mine the mirtirnum wire size (A.W.G.) extension cord. Use
only 3 wire extension cords which have 3-prong grounding
type plugs and 3-po)e receptacles which accept the tools
p l u g .
Wire Size A.W.G,
14
12
Exterision Cord Length
Up to 100 Ft.
100 - 200 Ft,
200 - 4 00 Ft. 8
CHECK MOTOR ROTATION
WARNING: FOR YOUR OWN SAFETY, MAKE SURE
PLUG iS NOT COt^NECTED TO POWER SOURCE OUT­
LET WHEN CHANGING MOTOR ROTATION.
The rnotor must rotate COUNTERCLOCKWISE when
viewed from the shaft end to which you witi mount the
pulley, (See -page 10-). |f ¡t does not, change the direction
according to the irtstructions furnished with the motor.