On off – E-Tech Series EGT EGF User Manual
Page 11
Page 11 / 80
ED, EG Rev. 2 - Operating Instructions
GB
Signal individual protection device
HAND PROTECTION
(gloves for protection against chemical, ther-
mal and mechanical risks).
5. TRANSPORTATION AND HANDLING
The product is packed to maintain the content intact.
During transportation avoid to stack excessive wei-
ghts. Ensure that during the transportation the
packed cannot move.
The transport vehicles must comply, for the weight
and dimensions, with the chosen product.
5.1 Handling
Handle with care, the packages must not receive
impacts.
Avoid to impact onto the package materials that
could damage the pump.
If the weight exceeds 25 Kg the package must be
handled by two person at the same time.
6 INSTALLATION
6.1 Dimensions
For the dimensions of the device see technical cata-
logue.
6.2 Ambient requirements and installation site
dimensions
The customer has to prepare the installation site in
order to guarantee the right installation and in order to
fulfill the device requirements (electrical supply,
etc...).
It's Absolutely forbidden to install the machine in an
environment with potentially explosive atmosphere.
6.3 Unpacking
Inspect the device in order to check any
damages which may have occurred during
transportation.
Package material, once removed, must be discar-
ded/recycled according to local laws of the destina-
tion country.
6.4. Pipes
The internal diameter of the delivery pipe must never
be smaller than the diameter of the pump connection
port:
G 1
1
/
2
(DN 40) for ED, EDV, EGN;
G 2
(DN 50) for EGT, EGF;
ATTENTION: The pump must be lifted and
transported using the handle fitted for this
purpose and not pulled by the electrical power
cable.
Place the pump, with vertical axis, at the bottom of
the pit or at the site of installation.
6.5. Stationary installation
Installation fit a check valve against back flow in the
delivery pipe ball valve (swing valve for EGN).
Provide for the possibility of removing the pump
without having to drain the entire system (if
necessary, fit a gate valve and a union coupling).
With the pump in the resting position secure the
delivery pipe to a rest, suitable for its length and
weight.
If slime deposits are expected to form at the bottom
of the installation pit, a support must be provided to
keep the pump raised.
6.6. Transportable installation
To avoid early deterioration of the pump when used
in stagnant water or in rivers, mount on a flat surface
raised from the ground so that sand or grit is not lif-
ted.
When a plastic delivery pipe or flexible hose is used,
a rope is required for lowering, securing and lifting
the pump.
A safety rope or chain of non-perishable material
should always be used to secure the pump.
i
min 550 x 550
3.93.037/3
h
max
h
min
mm
h
min
h
max
h
min
h
max
205
220
220
245
265
265
410
425
425
450
470
470
GQR 10-10
GQR 10-12
GQR 10-14
GQR 10-16
GQR 10-18
GQR 10-20
mm
h
min
h
max
mm
mm
mm
3.93.004/1
GQR
GQS, GQV 50-9
GQS, GQV 50-10
515
530
260
275
GQS, GQV 50-11
555
300
GQS, GQV 50-13
575
320
320 575
GQS, GQV 50-15
GMC 50...
GMV 50...
500
500
180
180
GMC 50-65..
505
185
GMC 50-65..
505
185
mm
h
min
h
max
225
240
240
265
285
315
330
330
355
375
h
max
h
min
min 300 x 250
3.93.037/3
GQRM 10-10 GF
GQRM 10-12 GF
GQRM 10-14 GF
GQRM 10-16 GF
GQRM 10-18 GF
GXV(M) 40-7
GXV(M) 40-8
508
533
248
273
GXV(M) 40-9 533 273
GXC(M) 40-10
GXC(M) 40-13
508
533
248
273
M
1
4.67.380
h
max
h
min
h
max
h
min
min 550 x 550
3.93.037/3
h
max
h
min
mm
h
min
h
max
h
min
h
max
205
220
220
245
265
265
410
425
425
450
470
470
EGN 4
EGN 5
EGN 7
EGN 9
EGN 11
EGN 15
mm
mm
mm
3.93.004/1
EGN
EGT, EGF 5
EGT, EGF 7
EGT, EGF 9
EGT, EGF 11
EGT, EGF 15
515
530
260
275
555
300
575
320
320 575
mm
h
min
h
max
225
240
240
265
285
315
330
330
355
375
h
max
h
min
min 300 x 250
3.93.037/3
GQRM 10-10 GF
GQRM 10-12 GF
GQRM 10-14 GF
GQRM 10-16 GF
GQRM 10-18 GF
EDV 5
EDV 7
EDV 9
ED 5
ED 9
508
533
248
273
533 273
508
533
248
273
M
1
4.67.380
h
max
h
min
h
max
h
min
On
Off
TYPE
TYPE
TYPE
TYPE
IST ED_ED_04_2015:MXS 11_03con gall 14/04/15 17:45 Pagina 11