Hatteland Display HT 221 (2U Size) - Manual (Page 55)

55
IND100241-17
Appendix
Pinout Assignments
Connectors illustrated here are either standard by factory default or may be available (through factory customization).
Note that some combinations may not be possible due to space restrictions. List also valid for customized models. All
pin out assignments are seen from users Point of View (POV) while looking straight at the connector. Please review
the dedicated datasheet or technical drawings for your actual unit to identify and determine the presence of desired
connector. Detailed information about Housing Connectors (terminal blocks) can be found earlier in this manual.
4-pin USB TYPE A
Pin 2: Negative Data
Pin 1: VCC +5V Pin 3: Positive Data
Pin 4: Ground
9-pin USB3.0 TYPE A
1 2 3 4
9 8 7 6 5
PIN 01 VCC +5V VBUS / Power
PIN 02 D- Negative Data
PIN 03 D+ Positive Data
PIN 04 GND Ground
PIN 05 StdA_SSRX- SuperSpeed Receive Negative Data
PIN 06 StdA_SSRX+ SuperSpeed Receive Positive Data
PIN 07 GND DRAIN Ground for signal return
PIN 08 StdA_SSTX- SuperSpeed Transmit Negative Data
PIN 09 StdA_SSTX+ SuperSpeed Transmit Positive Data
10-pin DisplayPort (DP) Female
20 18 16 14 12 10 8 6 4 2
19 17 15 13 11 9 7 5 3 1
PIN 01 ML_Lane 0 (p) - Lane 0 (positive)
PIN 02 GND - Ground
PIN 03 ML_Lane 0 (n) - Lane 0 (negative)
PIN 04 ML_Lane 1 (p) - Lane 1 (positive)
PIN 05 GND - Ground
PIN 06 ML_Lane 1 (n) - Lane 1 (negative)
PIN 07 ML_Lane 2 (p) - Lane 2 (positive)
PIN 08 GND - Ground
PIN 09 ML_Lane 2 (n) - Lane 2 (negative)
PIN 10 ML_Lane 3 (p) - Lane 3 (positive)
PIN 11 GND - Ground
PIN 12 ML_Lane 3 (n) - Lane 3 (negative)
PIN 13* CONFIG1 - connected to Ground*
PIN 14* CONFIG2 - connected to Ground*
PIN 15 AUX CH (p) - Auxiliary Channel (positive)
PIN 16 GND - Ground
PIN 17 AUX CH (n) - Auxiliary Channel (negative)
PIN 18 Hot Plug - Hot Plug Detect
PIN 19 Return - Return for Power
PIN 20 DP_PWR - Power for connector (3.3 V 500 mA)
*Pins 13 and 14 may either be directly connected to ground or
connected to ground through a pulldown device. This is the pinout for
source-side connector, the sink-side connector pinout will have lanes
0–3 reversed in order; i.e., lane 3 will be on pin 1(n) and 3(p) while
lane 0 will be on pin 10(n) and 12(p).
Serial COM RS-485/RS-422, 9-pin DSUB Male
“Full Duplex Mode*
1 2 3 4 5
6 7 8 9
PIN 01 TxD- Transmit Data Negative
PIN 02 TxD+ Transmit Data Positive
PIN 03 RxD+ Receive Data Positive
PIN 04 RxD- Receive Data Negative
PIN 05 GND Signal Ground
PIN 06 N/C No internal connection
PIN 07 N/C No internal connection
PIN 08 N/C No internal connection
PIN 09 N/C No internal connection
*Master only. ECHO not supported.
Serial COM RS-485/RS-422, 9-pin DSUB Male
“Half Duplex Mode*
1 2 3 4 5
6 7 8 9
PIN 01 Res. Reserved, do not connect
PIN 02 Res. Reserved, do not connect
PIN 03 Data+ Data Positive
PIN 04 Data- Data Negative
PIN 05 GND Signal Ground
PIN 06 N/C No internal connection
PIN 07 N/C No internal connection
PIN 08 N/C No internal connection
PIN 09 N/C No internal connection
*ECHO not supported.
Flow control: Via RTS signal (controlled by user application).
Note: Configuration performed in computer BIOS
Note: Configuration performed in computer BIOS