Heath Consultants Personal Surveyor (PS200 Series) User Manual
Ps200
Advertising
Table of contents
Document Outline
- TABLE OF CONTENTS
- COPYRIGHT
- LIABILITY
- MODIFICATION NOTICES
- SOFTWARE
- DISPOSAL ADVICE
- SAFETY
- AREAS OF USE
- SPECIAL CONDITIONS OF USE
- STORAGE, HANDLING AND TRANSIT
- WARRANTY
- DECLARATION OF CONFORMITY
- REVISION RECORD
- INTRODUCTION
- 1.1 GENERAL DESCRIPTION
- 1.2 FEATURES
- 1.3 DATA LOGGING
- 1.3.1 Archiving Stored Readings
- 1.4 FILTERS
- 1.5 CONSTRUCTION
- 1.6 IDENTIFICATION LABEL
- 1.7 CERTIFICATION
- 1.7.1 Certification Marks
- 1.7.2 Performance
- OPERATION
- 2.1 OPERATING PROCEDURE
- 2.2 SWITCH THE INSTRUMENT ON
- 2.2.1 Instrument Identification
- 2.2.2 Battery Status
- 2.2.3 User Name / Number Only (Option)
- 2.2.4 'Man Down' (Motion Sensor) Alarm Option
- 2.2.5 Date and Time
- 2.2.6 Bump Due Date (Option)
- 2.2.7 Calibration Due Date
- 2.2.8 Service Due Date (Option)
- 2.2.9 Select Calibration Gas (Option)
- 2.2.10 Sensor Confirmation Check
- 2.2.11 Memory Fault
- 2.2.12 Normal Operating Display
- 2.3 SWITCH THE DISPLAY BACKLIGHT ON / OFF
- 2.4 MANUAL DATALOG
- 2.5 VIEW MAXIMUM AND MINIMUM RECORDED VALUES SINCE SWITCH ON
- 2.6 ALARMS RESET OR ACKNOWLEDGE
- 2.6.1 Confidence Signal
- 2.7 REMOTE SAMPLING (with pump option)
- 2.7.1 Pump Operation:
- 2.8 SELF TEST
- 2.9 SWITCH THE INSTRUMENT OFF
- MANUAL BUMP TEST OPTIONS
- 3.1 BACKGROUND
- 3.2 MANUAL BUMP OPTIONS
- 3.3 INITIATING A MANUAL BUMP TEST
- 3.4 APPLYING TEST GAS
- 3.5 QUICK / FULL BUMP TEST
- 3.5.1 Quick Bump Test
- 3.5.2 Full Bump Test
- 3.6 ALARM CONFIRMATION
- 3.7 BUMP TEST RESULT
- ALARMS
- 4.1 GAS ALARMS
- 4.1.1 Flammable LEL Alarm Limit
- 4.1.2 Over-Range Flammable Gas Alarm Function
- 4.1.3 Oxygen (O2) Alarm Limits
- 4.1.4 Toxic Alarm Limits
- 4.2 ACKNOWLEDGE GAS ALARMS
- 4.3 MUTE ALARMS
- 4.4 HIGH FLAMMABLE GAS OVER-RANGE ALARM
- 4.5 FAULT ALARMS
- 4.5.1 Low Battery
- 4.5.2 Zero Fault
- 4.5.3 Sensor Fault
- 4.5.4 Low Flow - (Pumped instruments only)
- 4.5.5 Flow Fault (Pumped Instruments Only)
- 4.5.6 Calibration Required
- 4.5.7 Calibration Expired
- 4.6 'MAN DOWN' (MOTION SENSOR) ALARM
- OPERATOR MAINTENANCE
- 5.1 CLEANING
- 5.2 REPLACE INSTRUMENT FILTERS
- 5.2.1 Replace Sensor Hydrophobic Filter
- 5.2.2 Replace Sample Inlet (Dust) Filter
- 5.2.3 In-line Hydrophobic Filter (Accessory)
- RECHARGE BATTERY
- 6.1 RECHARGE INSTRUMENT BATTERY
- 6.1.1 Recharge Instrument using the Charging / Comms Clip
- 6.1.2 Recharge Instrument using the 5-way Charger
- 6.1.3 Recharge Instrument using the 12V / 24V In-Vehicle Charging Adaptor
- CALIBRATION
- 7.1 GENERAL DESCRIPTION
- 7.2 CALIBRATION VALIDITY
- ACCESSORIES
- ADDITIONAL INFORMATION
- 9.1 TRAINING
- 9.2 WORLD WIDE WEB
- TYPICAL OPERATING PARAMETERS
- PHYSICAL PROPERTIES
- ENVIRONMENT
- TYPICAL FLOW RATE INFORMATION
- WARM-UP / STABILIZATION TIME
- ALARMS
- DISPLAY
- POWER SOURCE
- CONSTRUCTION
- IP RATING
- RESPONSE TIMES (T90)
- INDEX
- INDEX
- Symbols
- A
- B
- C
- CALIBRATION
- Calibration, Automatic
- Calibration Due Date
- Calibration Expired
- Calibration, Field
- Calibration Gas
- Calibration Required
- CALIBRATION VALIDITY
- CERTIFICATION
- Certification Marks
- Charger, 5-way
- CLEANING
- CONFIDENCE BEEP
- Confidence Signal
- CONFIRMATION, ALARM
- Conformity, Declaration
- CONSTRUCTION
- COPYRIGHT
- CSA
- D
- E
- F
- G
- H
- I
- Identification, Instrument
- IDENTIFICATION LABEL
- In-line Hydrophobic Filter (Accessory)
- In-Vehicle Charging Adaptor
- INFORMATION, ADDITIONAL
- INITIATING A MANUAL BUMP TEST
- Inlet (Dust) Filter
- INSTRUMENT BATTERY
- INSTRUMENT FILTERS
- Instrument Identification
- INSTRUMENT OFF
- INSTRUMENT ON
- INTRODUCTION
- IP RATING
- IP65
- L
- M
- N
- O
- P
- Q
- R
- RATE, FLOW
- RATING, IP
- RECHARGE BATTERY
- RECHARGE INSTRUMENT BATTERY
- Recharge Instrument using the 12V / 24V
- Recharge Instrument using the 5-way Charger
- REMOTE SAMPLING
- REPLACE INSTRUMENT FILTERS
- Replace Sample Inlet (Dust) Filter
- Replace Sensor Hydrophobic Filter
- Required, Calibration
- RESET, ALARMS
- Resolution
- RESPONSE TIMES
- RESULT, TEST
- S
- SAFETY
- SAFETY, ADDITIONAL DETAILS - CSA ONLY
- Sample Inlet (Dust) Filter
- SAMPLING, REMOTE
- Select Calibration Gas
- SELF TEST
- Sensor Confirmation Check
- Sensor Fault
- Sensor Hydrophobic Filter
- SENSOR, MOTION
- Sensor, Motion
- Signal, Confidence
- SOFTWARE
- SOURCE, POWER
- Source, Power
- STABILISATION TIME
- Status, Battery
- STEL
- STORAGE
- T
- U
- V
- W
- Z