PermaGreen Triumph Spreader Sprayer - Manual (Page 25)

Spreader Operation
IMPORTANT: The Spreader requires periodic calibration and ad-
justment to verify the spreader pattern and to verify the correct
product delivery rate. Improper application of products can damage
turf or reduce the efficacy of applied products.
IMPORTANT: Check and adjust Spreader pattern daily, prior to
treating each lawn, and as needed to verify that the Spreader is
spreading properly.
IMPORTANT: Whenever you change products or rates of applica-
tion and at one-week intervals, or more frequently during heavy
use, verify that calibration is still valid. Adjust as necessary.
IMPORTANT: You should regularly compare the amount of product
used to the number of square feet covered to verify correct delivery
rate.
IMPORTANT: Use caution when spreading near desirable vegeta-
tion or painted surfaces to avoid damage.
IMPORTANT: Use caution when spreading in windy conditions to
avoid damage.
Description of Spreader features, controls, and operation
This machine uses a familiar 3-hole cyclone type spreader mecha-
nism that broadcast spreads a pattern width of 14 ± 1 feet (4.3 ±
0.3 meters). Using a 7 ± 1 foot (2.1 ± 0.3 meters) overlap travel
pattern provides an even distribution of most products. Referring to
FIGURE 10: A Deflector Lever (A) remotely controls a Deflector to
cut off the right side of the spread pattern for trimming. A Third-
hole Lever (B) remotely controls a Third-hole Adjustment Plate
that should be used with the Deflector to compensate for the
amount of product required while trimming and to balance the
spreader pattern for even distribution. An opening and closing
Hopper Lever (C) remotely controls the delivery of granular mate-
rial from the Hopper. A Rate Adjustment Knob (D) adjusts the
amount of product delivered when the hopper is open. The sprayer
can be operated at the same time the spreader is in use, and the
seven-foot overlap pattern is also effective for the sprayer.
Operation of Spreader Controls
Spreader Opening and closing.
• Start spreader operation by pushing the Hopper Lever (C) for-
ward to the OPEN position.
• To stop spreader operation, pull the Hopper Lever rearward to
the CLOSED position.
Spreader Rate adjustment.
• To increase the delivery rate, position the Rate Adjustment
Knob (D) at a higher number on the Rate Gage (not shown).
•
To decrease the delivery rate, position the Rate Adjustment
Knob rearward at a lower number on the Rate Gage.
Deflector operation.
• To raise the Deflector (not shown) out of the path of the granular
spread pattern, move the Deflector Lever (A) forward.
•
To lower the Deflector and interrupt the granular spread pattern
to the right of the spreader, pull the Deflector Lever rearwards.
Third-hole pattern adjuster operation when using the Deflector.
•
To close the Third-hole Adjustment Plate when lowering the
Deflector, pull the Third-hole Lever rearwards.
• To open the Third-hole Adjustment Plate (not shown), push the
Third-hole Lever forward.
Using the Third-hole pattern adjuster to balance the granular
spread pattern.
•
To reduce the amount of granular material spread towards the
right side of the machine, move the Third-hole Lever rearward to
partially close the Third-hole Adjuster Plate. NOTE: The gray
sliding Memory-Lock should be positioned to secure the Third-
hole Lever at that setting. The Lever pops into the Memory-
Lock to hold it in place. The Lever may then be used to close
the Third-hole Adjuster Plate and return to your pre-set Memory-
Lock position.
• To increase the amount of granular material spread towards the
right side of the machine, move the Third-hole Lever forward to
increase the opening of the Third-hole Adjuster Plate.
Spreader Operation
NOTE: For proper spreading the engine RPM (measured with the
machine in Neutral) MUST be maintained at 3,450 RPM, regard-
less of whether the machine is in High or Low Gear. If engine
RPMs are too low the spread width will be too narrow for effective
spreading. If too high, the spread width will be too wide.
NOTE: For proper spreading the spreader MUST be calibrated
(Refer to Spreader Calibration in this section).
For best results, It is recommended that products be applied using
one of the following methods:
Method 1: Make edging pass followed by parallel passes.
•
First make an edging pass around the perimeter of the property
and any ornamental beds etc.
• Pull the Deflector Lever to the rear to lower the Defector
while simultaneously pulling the Third-hole Lever rearward
to close the Third-hole Adjuster Plate and reduce the spread
width by cutting off the material on the right side.
•
Select the appropriate gear for the terrain and turf conditions.
•
Use LOW gear on inclines, slopes and/or hills and in tight
areas.
•
Use HIGH gear on level and open areas.
•
Set the Rate Adjustment Knob to the pre-calibrated rate for the
gear selected.
•
Pull the Throttle Lever to accelerate while simultaneously push-
ing the Hopper Lever forward to open the spreader and permit
granular material to flow from the Hopper.
21
Pesticide Safety
The improper use, handling, application, and disposal of pesticide
products applied by this machine may cause death or serious in-
jury.
•
Read and follow product label and Material Safety Data Sheet
(MSDS) precautions for handling, mixing, applying, and dispos-
ing of pesticides applied by this machine. Some materials may
present health hazards that will require the use of Personal
Protection Equipment (PPE). Always wear required PPE.
•
Keep required Personal Protection Equipment (PPE) available
for use by the operator or mechanic at all times.
•
Keep pesticide labels and MSDS available for the operator or
mechanic at all times.
20 FIGURE 10