Atlona AT UHD PRO3-88M - Manual (Page 22)

22
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Each command or feedback is terminated with a carriage return.
Note: If the command fails or is incorrect the feedback should be “Command FAILED”
To help with zone troubleshooting the matrix will broadcast “#*PORTXX_[feedback]” when
receiving any feedback from any zone.
RS-232 & TCP/IP Control Commands
The command codes are case sensitive, do not change capitalization, spacing, or lettering.
Command Feedback Description
PWON PWON Power on
PWOFF PWOFF Power off
PWSTA PWx Will display the power status of the matrix
Ex. Power is on, feedback will be PWON
Version Firmware # Brings up the current firmware version
Type Model # Brings up the model information
Lock Lock Locks the front panel of the matrix so no buttons are active
Unlock Unlock Unlocks the front panel of the matrix, enabling the buttons again
All# x1AVx1,x2AVx2,... Resets all inputs to corresponding outputs
Ex. input 1 to output 1, input 2 to output 2, input 3 to output 3, etc
x1$ x1$ Turns off output channel
Ex. to turn off output 3 = x3$
x1All x1All Sets selected input to all outputs
Ex. x3All would set input 3 to all
x1AVx2
Ex. x3AVx7
x1AVx2
Ex. x3AVx7
Switch input to output
Ex. input 3 to output 7
x1AVx2,x3,x4
Ex. x3AVx1,x4
x1AVx2,x3,x4
Ex. x3AVx1,x4
Switch input to multiple outputs
Ex. Switch input 3 to output 1 and 4
MirrorHdmiX OutY MirrorHdmiX OutY Mirror the HDMI output port with an HDBaseT output port
Ex. Mirror HDMI 6 with Output 1: MirrorHdmi6 Out1
UnMirrorX
Ex. UnMirror6
UnMirrorX
Ex. UnMirror6
Removes the chosen HDMI port from mirror mode
Ex. Unmirror HDMI 6 and no longer follows an HDBaseT output
VOUTX +
Ex. VOUT2 +
VOUTX (YY)
Ex. VOUT2 (-70)
Turns the volume of the chosen output (X) up one step
Ex. Turn the volume up from level -71dB to -70dB on analog output 2
VOUTX -
Ex. VOUT3 -
VOUTX (YY)
Ex. VOUT3 (12)
Turns the volume of the chosen output (X) down one step
Ex. Turn the volume down from level 13dB to 12dB on analog output 3
VOUTX (YY)
Ex. VOUT1 (-50)
VOUTX (YY)
Ex. VOUT1 (-50)
Set the volume of the chosen output (X) to a specific (YY) level
Ex. Set the volume to -50dB on output 1
VOUTX sta VOUTX (YY) Displays the current volume level of the chosen output (X)
VOUTMuteX Y
Ex. VOUTMute2 on
VOUTMuteX Y
Ex. VOUTMute2 on
Mute the volume level of the chosen analog output Y=on,off,sta
Ex. Mute the volume of analog output 2
IROFF IROFF Disables the front panel IR receiver window
IRON IRON Enables the front panel IR receiver window
Statusx1 x7AVx1 Shows what input is connected to selected output
Status x1AVx1,x2AVx2,
x3AVx4, .... Displays which inputs are currently connected to which outputs
SaveY
Ex. Save2
SaveY
Ex. Save2
Saves I/O route settings for future use, preset options 0 to 8
RecallY
Ex. Recall2
RecallY
Ex. Recall2
Recalls saved I/O route settings for the chosen preset number
ClearY
Ex. Clear2
ClearY
Ex. Clear2
Erases the saved I/O route settings for the chosen preset number
Mreset Mreset Sets matrix back to the default settings
RS232zoneX[command]
Ex. RS232zone1[PWRO]
RS232zoneX[command]
Ex. RS232zone1[PWRO]
Send commands to devices connected to the receiver RS-232 ports.
Commands are the same as the ones stated in this table. X = zone #
Ex. Turning the power on for the device connected in zone 1