Paslode IMCT Cordless Framing Nailer - Manual (Page 2)

2
Introduction and Warranty
Paslode Cordless Framing Nailer
Operating Manual
This manual is intended to acquaint you with the Paslode
Cordless Framing Nailer. Unlike other power fastening
tools, the Cordless Framing Nailer is powered by an
internal combustion linear motor. In simpler terms, your
Cordless Framing Nailer is powered by a motor similar to
the one that powers an automobile. The Cordless
Framing Nailer ignites a fuel and air mixture to produce
the energy to drive the motor, which in turn drives the
fastener. As you will see, the Cordless Framing Nailer is
totally self-contained. It carries its own fuel supply and
battery, along with a supply of fasteners.
For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out all of the
technical terms so that you can readily understand how
to get the maximum performance from your Cordless
Framing Nailer, and how to avoid damaging the tool or
injuring yourself. But, to accomplish this, we need you to
do two things:
1. READ THE MANUAL FROM COVER TO COVER
BEFORE USING THE TOOL.
2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.
The Cordless Framing Nailer should be handled like
other power fastening tools that you use. Like most tools,
when used improperly it could result in injury. If you are
going to allow others to use the Cordless Framing Nailer,
it is your responsibility to make sure that they also read
and comply with the instructions in this manual before
attempting to operate the tool.
Should you have questions about the Cordless Framing
Nailer, or wish to obtain additional copies of this manual,
please contact your Paslode ® representative. The space
below is provided so that you may record your
representative's name, address, and telephone number.
My Paslode representative is:
Name
Address
p i Z e t a t S y ti C
Telephone Number
Paslode ® Cordless Warranty and Limitations
Paslode warranties that new Paslode Cordless power fastening
tools, parts and accessories will be free from defects in material
and workmanship for the period shown below, after the date of
delivery to the original user.
ONE-YEAR LIMITED WARRANTY
A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.
FIVE-YEAR EXTENDED LIMITED WARRANTY
A five-year warranty will apply to all molded nylon parts:
• Motor Housing, Cap and Grille
• Handle Halves and Actuator
• Trigger
• Magazine Parts
90-DAY LIMITED WARRANTY
A 90-day warranty applies to the following parts, which are
considered normal wearing parts:
• Bumper
• Driver Blades
• O-Rings
• Seal Rings
WARRANTY STATEMENT
This warranty is limited to tools sold and service requested in the United
States. To obtain information on warranty service in the United States,
refer to the Service Center listing that was provided with your tool.
Paslode's sole liability hereunder will be to replace any part or accessory
which proves to be defective within the specific time period. Any replacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due to
normal wear.
This warranty is void as to any tool which has been subjected to misuse,
abuse, accidental or intentional damage, use with fasteners, fuel, batteries,
or battery chargers not meeting Paslode specification, size, or quality,
improperly maintained, repaired with other than genuine Paslode replacement
parts, damaged in transit or handling, or which, in Paslode's opinion, has
been altered or repaired in a way that affects or detracts from the performance
of the tool.
PASLODE MAKES NO WARRANTY, EXPRESSED OR IMPLIED, RELATING
TO MERCHANTABILITY, FITNESS, OR OTHERWISE, EXCEPT AS STATED
ABOVE, and Paslode's liability AS STATED ABOVE AND AS ASSUMED
ABOVE is in lieu of all other warranties arising out of, or in connection with,
the use and performance of the tool, except to the extent other wise provided
by applicable law. PASLODE SHALL IN NO EVENT BE LIABLE FOR ANY
DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT
NOT LIMITED TO, DAMAGES WHICH MAY ARISE FROM LOSS OF
ANTICIPATED PROFITS OR PRODUCTION, SPOILAGE OF MATERIALS,,
INCREASED COST OF OPERATION, OR OTHERWISE.
Paslode reserves the right to change specifications, equipment, or designs
at any time without notice and without incurring obligation.