Royal Cozyfires Super Hotbox Toaster MK4 - LPG - Manual (Page 4)

4 HM83 010710
1.2 IMPORTANT NOTES Super Hot Toaster Mk4
CAUTION – THIS PACKAGE WEIGHS 15Kgs – assess the load before you move it and note any other handling information
on the packaging. If you think the load is beyond your safe capability, DO NOT PUT YOURSELF AT RISK! Seek assistance
from other person(s) and/or use appropriate handling equipment. IT’S YOUR BODY – LOOK AFTER IT!
This appliance is for DECORATIVE PURPOSES ONLY and is manufactured to the requirements of the current issue of EN 509.
This appliance is for use on PROPANE GAS (G31) ONLY, at a supply pressure of 37mbar +/- 1mbar.
IN GREAT BRITAIN this appliance MUST be installed by a REGISTERED INSTALLER. Failure to do so may lead to prosecution.
Ventilation for this appliance must be fitted in accordance with the rules in force and checked regularly for obstructions.
If the appliance is installed in GREAT BRITAIN, additional ventilation is NOT normally required.
If the appliance is installed in IRELAND, a minimal cross sectional area of 100cm
2
is required.
Any permanent flue restriction must be removed and any variable dampers locked fully open or removed. If the flue has been used
previously for solid fuel, it MUST be swept PRIOR to installation.
If any soot accumulation becomes excessive, the fuel effect pieces should be removed from the appliance for cleaning. Cleaning
should be carried out in a sufficiently ventilated area or in the open air, by gently brushing with the pieces held away from your face so
that you avoid inhaling the dust. THE USE A NORMAL VACUUM CLEANER IS NOT RECOMMENDED as dust may be blown back
into the room.
This appliance has a naked flame and a fireguard, to the current issue of BS 8423 – 2002, should be used for the protection of
children, the elderly and the infirm.
Care must be taken on the selection of wall coverings within close proximity of the appliance as some vinyl and embossed materials
may become discoloured by convected heat. Soft furnishings must be kept clear from the radiant heat of the appliance and from
impinging the hearth area. Combustible materials must not be put on or left in the hearth area nor should the coal bed be used to burn
rubbish or other materials.
This appliance uses fuel effect components, gaskets and insulation material containing Refractory Ceramic Fibre, (RCF), which are
man-made vitreous silicate fibres. Excessive exposure to such material may cause temporary irritation to the eyes, skin and
respiratory tract. Consequently, it makes sense to take care when handling these articles to ensure that the release of dust is kept to a
minimum.
This appliance is fitted with an ODS, a spillage monitoring system which operates if the evacuation of products is interrupted (i.e.
blocked or incorrect flueing). If the appliance repeatedly `goes out’ it may indicate a problem and the installer or specialist should be
consulted before further use.
The minimum temperature rating of any back panel or hearth must have a minimum fire resistance rating of CLASS 0 (100
o C).
If any home improvements, e.g. double glazing, are carried out after this appliance has been installed, you should contact your
Registered Installer and have the operation of the flue checked.
1.3 LIGHTING AND EXTINGUISHING THE APPLIANCE
1. Remove the fret (Fig. 1), to gain access to the controls. (Fig. 2).
2. Press and turn the gas control anti-clockwise to the `IGN’ position. Keep the control fully depressed.
3. Once the main burner is lit, keep the gas control depressed for a further 15 seconds.
4. Release the gas control and check that the main burner has remained alight.
5. Press and turn the gas control anti-clockwise to the required setting. Replace the fret (controls cover).
6. To turn the appliance off, depress and turn the gas control clockwise from any position to the `OFF’ position.
7. In the event of the piezo ignition failing, the appliance may be lit by placing a lighted taper or match at the main burner while
depressing the gas control in the `IGN’ position.
IMPORTANT
After turning off or if the appliance goes out for any reason, wait for three minutes before attempting to relight.
Fret
Gas Control
Fig. 1
Fig. 2