Royal Cozyfires Super Hotbox Toaster MK4 - LPG - Manual (Page 7)

7 HM83 010710
Section 2 – Instructions for Installation
2.1 IMPORTANT NOTES Super Hot Toaster Mk4
CAUTION – THIS PACKAGE WEIGHS 15Kgs – assess the load before you move it and note any other handling information
on the packaging. If you think the load is beyond your safe capability, DO NOT PUT YOURSELF AT RISK! Seek assistance
from other person(s) and/or use appropriate handling equipment. IT’S YOUR BODY – LOOK AFTER IT!
This appliance is for DECORATIVE PURPOSES ONLY and is manufactured to the requirements of the current issue of EN 509.
This appliance is for use on PROPANE GAS (G31) ONLY, at a supply pressure of 37mbar +/- 1mbar.
IN GREAT BRITAIN this appliance MUST be installed by a REGISTERED INSTALLER. Failure to do so may lead to prosecution.
Ventilation for this appliance must be fitted in accordance with the rules in force and checked regularly for obstructions.
If the appliance is installed in GREAT BRITAIN, additional ventilation is NOT normally required.
If the appliance is installed in IRELAND, a minimal cross sectional area of 100cm
2 is required.
Any permanent flue restriction must be removed and any variable dampers locked fully open or removed. If the flue has been used
previously for solid fuel, it MUST be swept PRIOR to installation.
Care must be taken on the selection of wall coverings within close proximity of the appliance as some vinyl and embossed materials
may become discoloured by convected heat. Soft furnishings must be kept clear from the radiant heat of the appliance and from
impinging the hearth area. Combustible materials must not be put on or left in the hearth area nor should the coal bed be used to burn
rubbish or other materials.
This appliance uses fuel effect components, gaskets and insulation material containing Refractory Ceramic Fibre, (RCF), which are
man-made vitreous silicate fibres. Excessive exposure to such material may cause temporary irritation to the eyes, skin and
respiratory tract. Consequently, it makes sense to take care when handling these articles to ensure that the release of dust is kept to a
minimum.
This appliance is fitted with an ODS, a spillage monitoring system which operates if the evacuation of products is interrupted (i.e.
blocked or incorrect flueing). If the appliance repeatedly `goes out’ it may indicate a problem and the installer or specialist should be
consulted before further use.
The minimum temperature rating of any back panel or hearth must have a minimum fire resistance rating of CLASS 0 (100
o
C).
Materials used in the manufacture of this appliance DO NOT contain asbestos.
When fitting or servicing this appliance, care must be taken when handling sheet metal parts to avoid any possibility of personal injury.
If any home improvements, e.g. double glazing, are carried out after this appliance has been installed, you should contact your
Registered Installer and have the operation of the flue checked.
2.2 STATUTORY REQUIREMENTS
IN GREAT BRITAIN A REGISTERED INSTALLER must carry out the installation of this appliance in accordance with the current issue
and relevant requirements of:-
9 This installation booklet.
9 The gas safety (installation and use) regulations.
9 The
building regulations.
9 The building standards (Scotland) regulations.
9 The health and safety at work act.
9 The control of substances hazardous to health.
9 Any
applicable local regulations.
Detailed recommendations are contained in the current issue of the following British Standards and Codes of Practice:-
BS 5440 Part 1 Specifications for installation of flues.
BS 5440 Part 2
Specification for installation of ventilation for gas appliances.
BS 6461 Part 1 Codes of practice for masonry chimneys and flue pipes.
BS 5871 Part 3 Decorative fuel effect gas appliances of heat input not exceeding 15kW (2
nd
& 3
rd
family gases).
BS 6891 Specification for installation of low pressure gas pipe work of up to 28mm (R1) in domestic premises (2
nd
family gases).
BS 8303 Installation of domestic heating and cooking appliances burning solid mineral fuels.
BS 1251 Specification for open-fireplace components.
In IE the installation must be carried out by a competent engineer in accordance with:-
The current issue and relevant requirements of the installation booklet.
The rules in force and any local regulations.
IS 813 issued by the National Standards Authority of Ireland.
This installation booklet must not be taken as overriding statutory requirements.