Swim'n Play Slim Style Oval Pool - Manual (Page 33)

A reliable pool water test kit will help to determine the daily chlorine dosage and the acid-alkaline condition of the
water. You will find in the test kit two different color comparators. The yellow side is for chlorine. The color of your pool
water sample after adding some drops of chlorine indicator solution should be in the range of the color comparator of 0.3
to 0.6 p.p.m (parts per million). If the reading is below 0.3, add more chlorine to the water. If the reading is higher than
0.6 add fresh water to the pool or leave it unused until the reading drops. A too high content of chlorine will irritate the
skin and eyes. The pink side in the test kit will help you establish the acid-alkaline condition of the water. The color of
your pool water sample after adding some drops of pH indicator solution should be in the range of 7.2 pH to 7.6 pH of the
second color comparator. PH is the technical term for the measure of acidity or alkalinity of water. Readings below 7.0
indicate acidity, while readings higher than 7.0 indicate alkalinity. At 7.0 pH the water is neutral.
The pool water should be kept slightly alkaline at 7.2 to 7.6 pH. At this reading the water will be soft, comfortable and
the chlorine most effective. If the pH reading goes below 7.2 add soda ash. If the pH reading goes over 7.6 add sodium
bisulfate.
An acid condition will cause rapid consumption of the chlorine, irritation of eyes and skin and will corrode
the pool equipment. On the other hand a higher degree of alkalinity will slow down the chlorine action of killing
bacteria and algae, make the water cloudy and diminish its freshness. A higher than pH 7.8 alkaline condition of the
water will cause stiffness, brittleness, and considerable shrinkage of the liner. Since the chlorine compound is basically
alkaline, the continuous use of it will increase the alkalinity of the water.
At the beginning of the season treat your pool water with a water conditioner to prevent the building up of a high
degree of alkalinity. Some algae and bacteria become immune to low chlorine concentration, therefore, every two weeks
the pool should be super-chlorinated (shock treatment) with about double or even triple the normal dosage of chlorine.
Do not use the pool after shock treatment for at least 12 hours, then check chlorine content and pH and make sure both
are in the right balance.
At the start of the season use algaecides to prevent growing of algae and add it regularly to reduce chlorine
requirements.
Hard water: high content of minerals or iron in the water - often found in well water - will react with chlorine lowering
its action. By adding alum powder (turn off the filter during this process) coagulated particles will settle to the bottom and
the water will become soft. Do not use the pool for 24-48 hours, then turn on the filter, vacuum and check pH and chlo-
rine content. (Replace the filter element).
IMPORTANT HINTS:
Follow the label directions of the manufacturer when using chemicals. However, the real chemical balance depends
on various factors such as volume of pool water, temperature, exposure to sun, dirt and number of swimmers. Therefore,
make sure the reading for chlorine is always 0.3 to 0.6 p.p.m and the pH 7.2 to 7.6
Check the chlorine and pH every evening, when nobody is in the pool and adjust according to reading the necessary
amount of chemicals. Before using the pool the next day check again to make sure the water has the right chemical
balance. A strong chlorine smell above the pool water indicates evaporation of chlorine. More chlorine should be added
to the water. Be sure to check pH level again.
All chemicals must be dissolved thoroughly. Improperly dissolved chemicals may cloud the water, shorten the filter
cycle and damage the liner. A proper pH and the correct chlorine content of the pool water are essential for the protection
of all metal parts.
Keep filter running when adding diluted chemicals.
33
PREVENT DROWNING. NEVER SWIM ALONE. WATCH CHILDREN AT ALL TIMES.
KEEP A 4 FT. CLEAR SPACE AROUND POOL FREE
OF ANY OBJECTS THAT MAY PROVIDE ACCESS TO THE POOL
HOW TO KEEP WATER CLEAR AND HEALTHFUL
Your health, and maximum enjoyment is assured by keeping your pool water in sparkling clear and sanitary clean
condition. In order to obtain this condition certain equipment and chemicals available at your pool dealer are necessary.
Equipment, such as a filter according to the size of your pool, skimmer and a vacuum cleaner will take care of
removing suspended particles, leaves and oils from the water. A small wading pool for washing the feet of those entering
the pool and a pool cover when the pool is not in use are recommended to reduce dirt in the water. Utilizing this type of
equipment will keep your pool sparkling clear, but it will not purify the water. Purification (killing of bacteria and algae) is
accomplished by the use of chemicals.
Chlorine is the most commonly used bacteria killer for water. To make the chlorine work properly it is necessary to
keep the pool water at the proper acid-alkaline balance.