Extron electronic MTP 4T 15HD RS - Manual (Page 14)

MTP 4T 15HD RS • Reference Information
Reference Information
MTP 4T 15HD RS • Reference Information A-2 A-3
Specifications
Video
Gain ................................................ Unity
Number/signal type ..................... 4 sets of proprietary analog signals
Connectors .................................... 4 female RJ-45
Video input and loop through — per transmitter
Number/signal type ..................... 1 analog RGBHV, RGBS, RGsB, RsGsBs,
component video (with bi-level or
tri-level sync), S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs
local monitor loop through
(includes ID bits)
Connectors ..................................... 2 female 15-pin HD
Nominal level ................................ 1 Vp-p for Y of component video and
S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
0.3 Vp-p for C of S-video
Minimum/maximum levels ........ 0.3 V to 1.45 Vp-p
Impedance ..................................... 75 ohms
Horizontal frequency .................... 15 kHz to 130 kHz
Vertical frequency .......................... 30 Hz to 150 Hz
Return loss ..................................... <-30 dB @ 5 MHz
DC offset (max. allowable)........... 250 mV
Video output — see receivers’ specifications
Sync
Input type (transmitter) ............... RGBHV, RGBS, RGsB, RsGsBs, bi-level or
tri-level for component video
Output type (receivers) ................ RGBHV, RGBS, RGsB, RsGsBs
Standards ........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter) .............. 3.5 V to 5.5 Vp-p, unterminated
Output level (receivers) ................ 4.0 V to 5.0 Vp-p, unterminated
Input impedance .......................... 510 ohms
Output impedance ....................... 110 ohms
Max. input voltage ....................... 5.5 Vp-p
Polarity............................................ Positive or negative
Control/remote — external device (pass-through,
unidirectional or bidirectional)
Serial control port input/output . RS-232 via (1) 3.5 mm, 3 pole captive screw
connector
Serial control port output/input . 1 set of proprietary signals on a female
RJ-45 jack
N The serial communications link of an MTP RL 15HD RS or
MTP RL 15 HD RS SEQ is unidirectional only, transmitter to receiver,
unless the receiver’s directional jumper has been repositioned. The
jumper should be repositioned only when the receiver is the only one in
the system.
Baud rates ...................................... Up to 38400 bps at up to 600’ (183 m)
(Higher data rates and distances are
possible. Performance will vary based on
baud rate and cable length.)
Protocol ........................................... Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
N Protocol is mirrored between the transmitter and the receiver.
Serial control pin configurations . Captive screw connectors: 1 = TX, 2 = RX,
3 = GND
General
Power .............................................. 100 VAC to 240 VAC, 50/60 Hz, 20 watts,
internal
Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling ........................................... Convection, unvented
Rack mount .................................... Yes, with included mounting brackets,
part #70-077-03
Enclosure type .............................. Metal
Enclosure dimensions .................. 1.7" H x 17.5" W x 8.5" D
(1U high, full rack wide)
4.3 cm H x 44.4 cm W x 21.6 cm D
(Depth excludes connectors.)
Product weight .............................. 6.0 lbs (2.7 kg)
Shipping weight ........................... 10 lbs (5 kg)
Vibration ........................................ ISTA 1A in carton
(International Safe Transit Association)
Specs file:
MTP_4_T_15HD_RS_D3_112907.
pmd