ELAN Home Systems EM78P458 - Manual (Page 43)

EM78P458/459
OTP ROM
• If enabled, the comparator remains active and the interrupt remains functional, even under SLEEP
mode.
• If a mismatch occurs, the interrupt will wake up the device from SLEEP mode.
• The power consumption should be taken into consideration for the benefit of energy conservation.
• If the function is unemployed during SLEEP mode, turn off comparator before entering into sleep
mode.
4.11 The Initialized Values after Reset
Table 11 The Summary of the Initialized Values for Registers
Address Name Reset Type Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Bit Name C57 C56 C55 C54 C53 C52 C51 C50
Power-on 1 1 1 1 1 1 1 1
/RESET and WDT 1 1 1 1 1 1 1 1
N/A IOC50
Wake-up from Pin Changed P P P P P P P P
Bit Name C67 C66 C65 C64 C63 C62 C61 C60
Power-on 1 1 1 1 1 1 1 1
/RESET and WDT 1 1 1 1 1 1 1 1
N/A IOC60
Wake-up from Pin Changed P P P P P P P P
Bit Name /PD7 /PD6 */PD5 */PD4 /PD3 /PD2 /PD1 /PD0
Power-on 1 1 1 1 1 1 1 1
/RESET and WDT 1 1 1 1 1 1 1 1
N/A IOCB0
Wake-up from Pin Changed P P P P P P P P
Bit Name OD7 OD6 OD5 OD4 OD3 OD2 OD1 OD0
Power-on 1 1 1 1 1 1 1 1
/RESET and WDT 1 1 1 1 1 1 1 1
N/A IOCC0
Wake-up from Pin Changed P P P P P P P P
Bit Name /PH7 /PH6 /PH5 /PH4 /PH3 /PH2 /PH1 /PH0
Power-on 1 1 1 1 1 1 1 1
/RESET and WDT 1 1 1 1 1 1 1 1
N/A IOCD0
Wake-up from Pin Changed P P P P P P P P
Bit Name WDTE EIS X X X X X X
Power-on 1 0 1 1 1 1 1 1
/RESET and WDT 1 0 1 1 1 1 1 1
N/A IOCE0
Wake-up from Pin Changed P P 1 1 1 1 1 1
Bit Name X CMPIE PMW2IE PWM1IE ADIE EXIE ICIE TCIE
Power-on 0 0 0 0 0 0 0 0
/RESET and WDT 0 0 0 0 0 0 0 0
N/A IOCF0
Wake-up from Pin Changed 0 P P P P P P P
Bit Name OP2E OP1E G22 G21 G20 G12 G11 G10
Power-on 0 0 0 0 0 0 0 0
/RESET and WDT 0 0 0 0 0 0 0 0
N/A
IOC90
(GCON)
Wake-up from Pin Changed P P P P P P P P
Bit Name VREFS CE COE IMS2 IMS1 IMS0 CKR1 CKR0
Power-on 0 0 0 0 0 0 0 0
/RESET and WDT 0 0 0 0 0 0 0 0
N/A
IOCA0
(AD-CMP
CON)
Wake-up from Pin Changed P P P P P P P P
Bit Name PWM2E PWM2E T2EN T1EN T2P1 T2P0 T1P1 T1P0
Power-on 0 0 0 0 0 0 0 0
/RESET and WDT 0 0 0 0 0 0 0 0
N/A
IOC51
(PWMCON)
Wake-up from Pin Changed P P P P P P P P
Bit Name Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Power-on 0 0 0 0 0 0 0 0 N/A
IOC61
(DT1L)
/RESET and WDT 0 0 0 0 0 0 0 0
This specification is subject to change without prior notice. 07.01.2003 (V1.3) 43