Document Outline

• Contents
  • 1 Mounting 6
  • 2 Electrical connections 7
    • 2.1 Connecting diagram 7
    • 2.2 Terminal connection 8
  • 3 Operation 12
    • 3.1 Front view 12
    • 3.2 Behaviour after power-on 13
    • 3.3 Operating level 13
    • 3.4 Error list / Mainenance manager 14
    • 3.5 Self-tuning 17
      • 3.5.1 Preparation for self-tuning 17
      • 3.5.2 Optimization after start-up or at the set-point 18
      • 3.5.3 Selecting the method ( ConF / Cntr / tunE ) 18
      • 3.5.4 Self-tuning start 22
      • 3.5.5 Self-tuning cancellation 22
      • 3.5.6 Acknowledgement procedures in case of unsuccessful self-tuning 23
      • 3.5.7 Examples for self-tuning attempts 24
    • 3.6 Manual self-tuning 25
    • 3.7 Second PID parameter set 26
    • 3.8 Alarm handling 27
    • 3.9 Operating structure 29
  • 4 Configuration level 30
    • 4.1 Configuration survey 30
    • 4.2 Configuration parameters 31
    • 4.3 Set-point processing 49
      • 4.3.1 Set-point gradient / ramp 49
    • 4.4 Switching behaviuor 50
      • 4.4.1 Standard ( CyCl= 0 ) 50
      • 4.4.2 Switching attitude linear ( CyCl= 1 ) 50
      • 4.4.3 Switching attitude non-linear ( CyCl= 2 ) 51
      • 4.4.4 Heating and cooling with constant period ( CyCl= 3 ) 52
    • 4.5 Configuration examples 53
      • 4.5.1 On-Off controller / Signaller (inverse) 53
      • 4.5.2 2-point controller (inverse) 54
      • 4.5.3 3-point controller (relay & relay) 55
      • 4.5.4 3-point stepping controller (relay & relay) 56
      • 4.5.5 Continuous controller (inverse) 57
      • 4.5.6 D - Y - Off controller / 2-point controller with pre-contact 58
      • 4.5.7 8800 process controller with measured value output 59
      • 4.5.8 Continuous controller with integrated positioner ( Cntr/ C.Fnc = 6 ) 60
  • 5 Parameter setting level 61
    • 5.1 Parameter survey 61
    • 5.2 Parameters 62
    • 5.3 Input scaling 65
      • 5.3.1 Input Inp.1 and InP.3 65
      • 5.3.2 Input InP.2 66
  • 6 Calibration level 67
  • 7 Special functions 70
    • 7.1 DAC®Œ motor actuator monitoring 70
    • 7.2 O2 measurement 72
      • 7.2.1 Connection 72
      • 7.2.2 Configuration: 73
    • 7.3 Linearization 74
    • 7.4 8800 process controller as Modbus master 75
  • 8 8800/8840 configurator 76
  • 9 Versions 77
  • 10 Technical data 78
  • 11 Safety hints 81
    • 11.1 Resetting to factory setting 82
  • 12 Notes 83
• Index
  • 0-9
    • 2-point correction 67
  • A
    • Alarm handling 28 - 29
  • B
    • Bargraph 12
    • Bus interface
      • Technical Data 81
    • C
      • Calibration level (CAL) 67 - 69
      • Certifications 82
      • Configuration examples
        • 2-point controller 55
        • 3-point controller 56
        • 3-point stepping controller 57
        • Continuous controller 58
        • D - Y -Off controller 59
        • Measured value output 60
        • Signaller 54
      • Configuration level
        • Configuration parameters 32 - 49
        • Parameter survey 31
      • Connecting diagram 7
      • Connecting examples
        • di2/3, 2-wire transmitter supply 9
        • INP2 current transformer 8
        • OUT1/2 heating/cooling 8
        • OUT3 as logic output 11
        • OUT3 transmitter supply 10
        • RS485 interface 10
      • Control inputs di1, di2, di3
        • Technical data 78
      • Cooling functions
        • Constant period 53
        • Standard 51
        • Water cooling non-linear 52
      • Current signal measuring range 78
  • • DAC 70 - 71
    • Digital inputs di1, di2, di3
      • Configuration 44
      • Technical data 78
  • E
    • Environmental conditions 81
    • Equipment 77
    • Error list 15
  • F
    • Front view 12
  • I
    • Input INP1
      • Configuration 33
      • Parameters 64
      • Technical data 78
    • Input INP2
      • Configuration 35
      • Parameters 64
      • Technical data 78
    • Input INP3
      • Configuration 35
      • Parameters 65
      • Technical data 78
    • Input scaling 66
  • L
    • LED
      • Ada - LED 12
      • Err - LED 12
      • func - LED 12
      • ì - LED 12
      • LED colours 12
      • ò - LED 12
      • para - LED 12
      • SP.2 - LED 12
      • SP.E - LED 12
    • Linearisierung 74
  • M
    • Mainenance manager 15 - 17
    • Manual tuning 26
    • Modbus master 75
    • Mounting 6
  • N
    • Notes 86 - 87
  • O
    • O2-Messung 72
    • Offset correction 67
    • Optimierung am Sollwert 20
    • Output OUT1
      • Configuration 39
      • Technical data 79
    • Output OUT2
      • Configuration 40
      • Technical data 79
    • Output OUT3
      • Configuration 41
      • Technical data 79
    • Output OUT4
      • Configuration 42
      • Technical data 79
    • Output OUT5
      • Configuration 44
      • Technical data 80
    • Output OUT6
      • Configuration 44
      • Technical data 80
  • P
    • Parameter setting level
      • Parameter survey 62
      • Parameters 63 - 65
    • Parameter Sollwertgradient 64
  • R
    • Resetting to factory setting 85
    • Resistance thermometer measuring range 78
  • S
    • Safety hints 84 - 85
    • Safety switch 6
    • Safety test 81
    • Sauerstoffmessung 72
    • Self-tuning
      • Cancelation 23
      • Cancelation causes 24
    • Set-point processing 50
  • T
    • Thermocouple measuring range 78
  • • Versions 77
    • Voltage signal measuring range 78