FUJITSU 560H - Manual (Page 3)

560H Series Connector Conforming to Ver. 4
3
Dimensions are in millimeters (inches) www.fcai.fujitsu.com
Specifications
subject to change
RIGHT-ANGLE PLUG, THROUGH HOLE TYPE (WITH NO EJECTOR, STANDARD TYPE)
SUPPORTS TYPE I, II CARDS
■ DIMENSIONS AND PC BOARD MOUNTING HOLE LAYOUT (MOUNTING SIDE)
RIGHT-ANGLE PLUG, THROUGHHOLE TYPE
(((((
WITH NO EJECTOR, LOW-PROFILE TYPE
)))))
SUPPORTS TYPE I, II CARDS
■ DIMENSIONS AND PC BOARD MOUNTING HOLE LAYOUT (MOUNTING SIDE)
Unit: mm (in.)
Part number: FCN-565P068-G/C-V4
3
(0.118)
4
(0.157)
1.51 (0.059) 1.905 (0.075) 3.810 (0.15) 5.715 (0.225)
50.8 (2)
1.27 (0.05) Ч (34-1) = 41.91 (1.65)
1.27 (0.05)
3
(0.118)
42 (1.65)
12.2 (0.48)
58.7 (2.31)
24.9 (0.98)
1.27 (0.05)
1.27 (0.05)
1.27 (0.05) Ч (34-1) = 41.91 (1.65)
No.1
No.35 No.68
No.34
2- ø 2.8 (0.11)
2.5mm (0.098)
deep spot facing
3.6 (0.141)
Part number: FCN-565P068-G/01-V4
• Models with a board lock (metal fitting for direct mounting) are also available. Part number: FCN-565P068-G/12-V4 (for 1.2 mm (0.047 in.) to 1.6 mm (0.063 in.) thick PC board)
FCN-565P068-G/08-V4 (for 1.0 mm (0.039 in.) thick PC board)
• Long-terminal models are also available. Part number: FCN-565P068-G/13-V4 (4 mm (0.157 in.))
FCN-565P068-G/02-V4 (10 mm (0.394 in.))
• Models which support Type III are also available. Part number: FCN-565P068-G/17-V4
FCN-565P068-G/18-V4 (with board lock, for 1.2 mm (0.047 in.) to 1.6 mm
(0.063 in.) thick PC board )
Unit: mm (in.)
50.8 (2)
0.51 (0.02)
1.905 (0.075)
3.810 (0.15)
5.715 (0.225)
7 (0.276)
3 (0.118)
11.2 (0.44)
5 (0.197)
1 (0.039)
4.25 (0.167)
3.5 (0.138)
2- ø 2.8 (0.110)
41.91 (1.65)
1.27 (0.05)
59.7(2.35)
2.42 (0.095)
35.2 (1.39)
2.5mm (0.098)
deep spot facing
41.91 (1.65)
1.27 (0.05)
No.17
No.51
No.34
No.68 No.35
No.1
1.27 (0.05)
4 (0.157)
50.8 (2) ±0.1 (0.0039)
41.91 (1.65) ±0.1 (0.0039)
1.27 (0.05) ±0.05 (0.0020)
No.3
No.1
No.2
5.715 (0.225) ±0.05 (0.0020)
3.810 (0.15) ±0.05 (0.0020)
1.905 (0.075) ±0.05 (0.0020) No.68
2- ш 2.8 (0.110) ±0.1 (0.0039)
68- ш 1 (0.039) ±0.05 (0.0020)
(Card insertion side)
50.8 (2) ±0.1 (0.0039)
41.91(1.65) ±0.1 (0.0039)
1.27 (0.05) ±0.05 (0.0020)
No.3
No.1
No.2
5.715 (0.225) ±0.05 (0.0020)
3.810 (0.15) ±0.05 (0.0020)
1.905 (0.075) ±0.05 (0.0020) No.68
2- ш 2.8 (0.110) ±0.1 (0.0039)
68- ш 1 (0.039) ±0.05 (0.0020)
(Card insertion side)
Use M2.5 (0.098 in) nut and screws. Screw torque is 3.2 kg/cm.
In order to avoid damage to the connector, do not pull out the card at an angle.