Fostex DE-10 - Manual (Page 17)

17
DE-10 Owner’s Manual
MIC/G LINE
TRIM
GUITAR
MIC
model 8051 SINGLE MODE
DUAL MODE 2
(MONO)
1 (1&2)
LINE INPUT (-10dBV) OUTPUT 2 OUTPUT 1 EFF MUTE
MAX MIN MIN MAX
MIC/GUITAR INPUT
FOOT SW
R
R L
(MONO)
R L
L(MONO)
1 2 3 4 5 6 7 8
1. Power cord
2. FOOT SW jack
By connecting the optional Model 8051 foot switch to this
jack, you can alternate on or off of the EFFECT MUTE
function via the foot switch.
Names and Functions
(Rear panel section)
8. MIC/GUITAR INPUT jack and TRIM control
This jack is used to connect to a microphone or guitar.
It is active when the input select switch is set to "MIC/G".
In the dual mode, the source signal is routed to EFFECT 1.
When the INPUT 2 (R) jack is not plugged, the same signal
is fed to both EFFECT 1 and EFFECT 2. You can adjust the
input level by the control beside the jack while
monitoring the appropriate peak indicator.
In the single mode, the source signal is routed to the L
channel of the effect. When the INPUT 2 (R) jack is not
plugged, the same signal is fed to both the L and R
channels of the effect.
You can adjust the input level by the TRIM control beside
the jack while monitoring the appropriate peak indicator.
The MIC/GUITAR INPUT jack is active. You can
connect a microphone or guitar directly.
The LINE INPUT jack is active. You can con-
nect a line level source.
LINE
MIC/G
7. Input select switch
Selects the input jack to be active for INPUT 1.
3. OUTPUT 2 jacks (L (MONO), R)
In the dual mode, these jacks feed the EFFECT 2 sound in
stereo (L and R). In the single mode (1 or 2), they do not
feed any signal. When only the "L (MONO)" jack is plugged,
it feeds the summed signal of L and R.
4. OUTPUT 1 jacks (L (MONO), R)
In the dual mode, these jacks feed the EFFECT 1 sound in
stereo (L and R). In the single mode, they feed the
selected effect sound in stereo (L and R). When only the
"L (MONO)" jack is plugged, it feeds the summed signal of
L and R.
5. LINE INPUT 2 jack/Input level control
This jack is used to connect to a line level (-10 dBV) source.
In the dual mode, the source signal is routed to EFFECT 2.
You can adjust the input level by the control beside the
jack while monitoring the appropriate peak indicator.
In the single mode, the source signal is routed to the R
channel of the effect.
You can adjust the input level by the input level control
beside the jack while monitoring the appropriate peak
indicator.
Contact our dealer or local Fostex sales office if you
want to know details about the Model 8051.
6. LINE INPUT 1 jack and Input level control
This jack connects to a line level (-10 dBV) source.
It is active when the input select switch is set to "LINE".
In the dual mode, the source signal is routed to EFFECT 1.
When the INPUT 2 (R) jack is not plugged, the same signal
is fed to both EFFECT 1 and EFFECT 2. You can adjust the
input level by the control beside the jack while
monitoring the appropriate peak indicator.
In the single mode, the source signal is routed to the L
channel of the effect. When the INPUT 2 (R) jack is not
plugged, the same signal is fed to both the L and R
channels of the effect.
You can adjust the input level by the input level control
beside the jack while monitoring the appropriate peak
indicator.
<NOTE>
When the input select switch is set to "MIC/G", this
jack is not active.
<NOTE>
When the input select switch is set to "LINE", this jack
is not active.