Fostex VF08 - Manual (Page 14)

Making an audio CD
The following procedure describes how to record mastered songs (using the internal mastering function) to a CD-
RW/CD-R disc to make an audio CD (CD-DA format).
The
“Save PGM” menu in the Setup mode, which is used for saving song data, is also used for making an audio CD.
<Basic information>
When making an audio CD using the VF08, inter-
nal mastering materials on the current drive are
recorded to a CD-RW/CD-R disc (by the CD-DA for-
mat).
As we explain in “Save/load of Song Data using a
CD-RW drive” on page 9, you can record not only a
single song but also multiple songs continuously.
When recording more that one songs continuously,
the VF08 automatically inserts a 2-second silent
space between songs. VF08
CD-RW/CD-R disc
In the following procedure, we assume that one or
more mastering programs exist and a CD-RW drive is
connected to the SCSI port of the Model 8340 installed
in the VF08 and a non-recorded CD-RW/CD-R disc is
used.
1. After turning on the power of both the VF08 and a
connected CD-RW drive, load a non-recorded disc to the
CD-RW drive.
2. Press the [SETUP] key to enter the Setup mode.
3. Use the [JOG] dial to select (highlight) the “Save PGM”
menu and press the [ENTER/YES] key.
The display shows the screen for selecting the device to
which the data is saved.
“SCSI” flashes.
<Note>
Key operations of the VF08 should be done after
completing access to a CD-RW/CD-R disc.
4. Press the [ENTER/YES] key while “SCSI” flashes.
After showing the model name of the connected CD-RW
drive, the display shows the screen for selecting the save
mode, in which
“BkUp” flashes.
To carry out making an audio CD, select “CD-DA” .
If you need to change the copy protection setting (the
default setting is
“OFF” ), select “Setup” (for setting
writing conditions). If you make an audio CD without
changing the copy protection setting, skip steps 5 and 6
below and go to step 7.
flashing
5. Use the [JOG] dial (or the [CURSOR] < > key) to select
“Setup” and press the [ENTER/YES] key.
The display shows the “CD-DA Setup” screen, on which
you can select the copy protection setting (see the next
page).
<Figure-1>
<Figure-2>
<Note>
If an audio CD is made using a CD-RW disc, it
can be played back only by a player that sup-
ports CD-RW playback. You cannot playback such
a disc by a conventional CD player that does not
support CD-RW playback.
DIGITAL MULTITRACKER
LOCATE ABS 0 LOCATE REC END
SEL TIMEBASE
CURSOR
PHANTOM
ACCESS
PEAK CH ON/OFF
L R
GUITAR GUITAR
LINE MIC LINE MIC MIN MAX
MASTERING TRAINING
EFFECT EQ PAN
SCENE SEQ. SCENE TRACK
UNDO SETUP
PUNCH AUTO LOOP PITCH SCRUB VARI
F FWD REWIND PLAY STOP RECORD
EXIT
ENTER
TRIM TRIM
WAVE FORM
MIX PARAMETER
PGM FADER MAP
ON/OFF 2TRK MODE
F1 F2 F3 SHIFT
EDIT EDIT EDIT MARK DELETE
LOCATE
FOOT SW ST OUT PHONES INPUT A
BOUNCE MODE
INPUT B
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
+6
-10
-20
-40
- ∞
-30
0
PEAK CH ON/OFF
2 3 4 5 6 7/8 2TRK 1 MASTER
TRACK STATUS / TRACK SEL TRACK STATUS RED REC GREEN PLAY OFF MUTE STATUS /SEL
EJECT
/YES
/NO
SHUTTLE JOG
UNBAL UNBAL
BAL BAL
F1 F2 F3
EDIT
/REDO
14
Silence (about 2 seconds)
Start point End point
1 2 3
Start point End point
Start point End point
flashing