Great Dane GSRKA1934S - Manual (Page 44)

GETTING QUALITY SERVICE
GETTING QUALITY SERVICE - 42
If oil is level is below ADD mark, fill to proper
level.
If oil level is above the FULL mark, drain to
proper level.
Insert dipstick. Tighten cap.
Connect Battery
CAUTION: Avoid injury! Prevent Battery Explosions:
• Keep sparks, lighted matches, and open flame away from
the top of battery. Battery gas can explode.
• Never check battery charge by placing a metal object
across the posts. Use a volt-meter or hydrometer.
• Do not charge a frozen battery; it may explode. Warm bat-
tery to 16 degrees C (60 degrees F).
Connect positive (red) cable to battery positive (+)
terminal. Install red terminal cover (A).
Connect negative (black) cable to battery negative (-)
terminal. Install black terminal cover (B).
Check Machine Safety Systems
Perform safety system check to make sure the electronic
safety interlock circuit is functioning properly.
Specifications
Engine
Note: See engine manufacturer’s owner’s manual provided
with your machine for engine specifications.
Drivetrain
Type........................................................ Dual Hydrostatic
Pumps.........Hydro-Gear PG-1KDA-D61 - PG-1HDA-D41
Wheel Motors..........................Hydro-Gear HGD-12-7172
Number of Speeds.................................Infinitely Variable
Electrical System
Charging System..................................................15 Amp
Ignition................................................................Flywheel
Starter.........................................................Solenoid Shift
Fuel System
Fuel Type..............................Gasoline, Regular Unleaded
Fuel Tank Location...................On Right Side of Operator
Fuel Capacity ............................................22.7 L (6.0 gal)
Steering and Brakes
Steering.............................................Dual Control Levers
Steering..............................................................Hydraulic
Park Brake.....................................................Tire Contact
•
•
5.
1.
2.
Tires
Rear.................................................................18 x 6.5 - 8
Front...................................................................11 x 4 - 5
Inflation Rear (Maximum)..............69–97 kPa (10–14 psi)
Inflation Front (Maximum)..........138–173 kPa (20-25 psi)
Battery
Voltage....................................................................12-volt
CCA.....................................................................270-amp
Reserve Capacity.............................................67 minutes
BCI Group Size.............................................................U1
Capacities
Fuel Tank......................................................18.9 L (5 gal)
Hydraulic Oil (With Filter) 3.1 L (3.3 qt.)
Engine Oil (With Filter) 1.9 L (2.0 qt.)
Travel Speeds at Full Engine RPM
Forward........................................0–14 km/h (0–8.7 mph)
Reverse..........................................0–6.4 km/h (0–4 mph)
Dimensions
Overall Height............................................1.47 m (47 in.)
Overall Length.........................................1.48 m (58.5 in.)
Overall Width (with chute up)....................... .89 m (35 in.)
Overall Width (with chute down).................1.19 m (47 in.)
Recommended Lubricants
Engine Oil.........................See Applicable Engine Manual
Hydraulic Oil................5W-50 or 15W-50 All Synthetic Oil
Grease: (This may change for high-speed applications such
as cutting units)
All-Purpose Grease with an NLGI Grade No. 2 Rating
(Specifications and design subject to change without
notice.)
Getting Quality Service
Service Literature
If you would like to order a copy of the Parts Catalog or
Operator Manual for this machine, contact your Great Dane
Dealer. Parts catalogs and operator manuals are also avail-
able online at Great Dane.com.
Parts
We recommend Great Dane quality parts available at your
Great Dane dealer.
Part numbers may change, use part numbers listed below
when you order. If a number changes, your dealer will have
the latest number.
When you order parts, your Great Dane dealer needs your
machine serial number and engine serial number. These
are the numbers that you recorded in the Product Identifica-
tion section of this manual.