Marantz ZR6001 User Manual
Page 13
ENGLISH
10
OPERATION OF REMOTE CONTROL
UNIT
REMOTE CONTROL
The distance between the transmitter of the
remote control and the IR SENSOR of the ZR6001
should be less than 5 meters. If the remote control
is pointed in a direction other than the IR SENSOR
or if there is an obstacle between them, use of the
remote control may not be possible.
Remote-controllable range
LOADING BATTERIES
The life of the batteries used with the remote
control is about 4 months with normal use. Also be
sure to replace batteries earlier when you notice
that they are getting weak.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with
correct
and
polarity.
3.
Close the cover until it clicks.
Notes:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
CAUTIONS ON BATTERIES
• Use “AAA” type batteries in this remote control
unit.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying
operation. Replace it with a new battery as soon
as possible.
• When inserting the batteries, be careful to do so
in the proper direction, following the + and -
marks in the remote control unit’s battery
compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules that
apply in your country or area.
TUNER MODE
AMP MODE
GENERAL INFORMATION OF RC5500SR TO ZR6001
To control the ZR6001 by your RC5500SR, you have to select the device AMP or TUNER by pressing the
function selector button. Please refer below for the details in AMP and TUNER mode.
SU
RR
O
UN
D
AV
SU
RR
OU
ND
RE
CE
IVE
R Z
R60
01
DOW
N
U
P
VO
LU
M
E
IN
PU
T S
ELE
CT
O
R
PO
W
ER
O
N/O
FF
PH
O
NE
S
ST
AN
DBY
M
UT
E
M
UL
TI
M
. S
PE
AK
ER
B
PU
RE
SET
UP
D
IRE
C
T
SIMP
LE
AU
TO
HT
-E
Q
M
EN
U
EN
TER
D
IS
PL
A
Y
M
EM
O
RY
CLE
AR
T-M
O
DE
EX
IT
BA
ND
M
O
DE
AU
X
1 IN
PU
T
AU
DIO
S-V
ID
EO
VID
EO
L
R
7.1
CH
IN
PUT
Remote control unit (RC5500SR)
60
°
ZR6001
Approx. 5 m
CH.SEL
LIP.SYNC
PTY
SUB-T/ATT
AUDIO
INPUT/DISC+
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
MENU
OSD
VOL.
TV
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
SYSTEM REMOTE CONTROLLER
RC5500SR
VOL.
MAIN
ENTER
AUX1
ENTER
CH.SEL
LIP.SYNC
PTY
SUB-T/ATT
AUDIO
INPUT/DISC+
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
SYSTEM REMOTE CONTROLLER
RC5500SR
AUX1
POWER
Turns the ZR6001 on and off
Function selector * Selects a particular source component
SLEEP *
Sets the sleep timer function
MUTE *
Decreases the sound temporarily
VOL
34
*
Adjusts the over all sound level
MENU
Enters the SETUP MENU
Cursor
Moves the cursor for settings in the SETUP MENU
ENTER
• Enters the SETUP MENU
• Confirms the settings in SETUP MENU
SETUP/T.TONE
Enters the test tone mode for setting the Speaker Level Setup
MENU OFF
Exits from the SETUP MENU
PURE DIRECT * Selects the Pure Direct mode
NIGHT *
Turns on or off the NIGHT mode
DISPLAY *
Change the front display mode
Surround mode (1-8) Selects the surround mode
7.1CH-IN (9)
Selects the 7.1CH IN
A/D (0)
Switches between the analog and digital inputs
BASS
34
*
Adjusts the tone control of low frequency sound
TREBLE
34
*
Adjusts the tone control of high frequency sound
SUB-T/ATT
Reduces the input level
P.SCAN/V-OFF
Turns on or off the Video output
CH. SEL
Adjusts the input level
LIP.SYNC
Selects the LIP. SYNC mode
* These buttons are used to control ZR6001 in any function mode.
TUNER
Selects a frequency band
0-9
Inputs the numeric #s
CLEAR
Clears the inputting
MEMO
Enters the tuner preset memory numbers
P.SCAN/V-OFF
Starts preset scan
CHANNEL/SKIP
• Selects a preset station
4
/
¢
TUNE/SEARCH
Tunes a station
5
/
6
T-MODE
1
2
Selects the auto stereo mode or mono mode
F.DIRECT
2
Selects the “Frequency direct input”
06.3.6, 4:27 PM
Page 10