Other function, Surround – Marantz ZR6001 User Manual
Page 34
ENGLISH
31
OTHER FUNCTION
TV AUTO ON/OFF FUNCTION
This function allows the component connected to
the TV-VIDEO in jack to control the power (ON/
OFF) to the ZR6001.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED.
(Refer page 22 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
ZR6001.
4.
Turn ON the TV TUNER and tune in a
receivable station.
5.
When the station is received, the ZR6001
turns ON and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER
OFF or select a channel that does not contain
any broadcast.
2.
The power to the ZR6001 switches to
STANDBY after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the ZR6001 is
set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV
AUTO ON/OFF” function.
ATTENUATION TO ANALOG INPUT
SIGNAL
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“
PEAK
” indicator will light up on the front display.
If this happens, you should press the
ATT
button
on the remote.
“
ATT
” indicator will be illuminated when this
function is activated. The signal-input level is
reduced by about half. Attenuation will not work
with the output signal of TAPE-OUT, CD-R/MD-
OUT, VCR1-OUT and DSS/VCR2-OUT.
This function is memorized for each individual
input source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the ZR6001’s
output through a pair of headphones. Be certain
that the headphones have a standard 1/4” stereo
p h o n o p l u g . ( N o t e t h a t t h e s p e a k e r s w i l l
automatically be turned off when the headphone
jack is in use.)
Note:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the
MENU
button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the
MENU
button is
pressed is shown below.
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
→
→
→
→
BYPASS : Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
DH1 : The size of a typical living room space
is simulated.
DH2 : The expansiveness of a structure as
large as a music hall is simulated.
DH3 : A large space such as that found in a
movie theater is simulated.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “
✽✽✽
” is
displayed as the mode indication.
The surround mode can be selected when any of
the modes in DH1, DH2, or DH3 is selected.
L/R LEVEL can be set in the
±
10 dB range.
Notes:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
• TONE cannot be set when any of the modes in
DH1, DH2, or DH3 is selected.
• The Dolby Headphone function will not work
when 32 or 96 kHz PCM digital signals are input.
VIDEO ON/OFF
When no video signal is connected to the ZR6001
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the “
VIDEO OFF
” setting.
To select video off, press the
AMP
button and
press the
V-OFF
button.
DISPLAY MODE
You can select the display mode for the front
display of the ZR6001.
To select this mode, press the
DISPLAY
on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
→
Surround Mode
→
Auto-display Off
→
Display
Off
→
Input Function
→
Surround Mode....
In Auto display off mode, the display is off. But, if
you make a change to the unit such as input or
surround mode, the display will show that change,
then go back to off after about 3 seconds. When
changing the volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition
CH.SEL
LIP.SYNC
PTY
SUB-T/ATT
AUDIO
INPUT/DISC+
F.DIRECT
RDS
T-MODE
SYSTEM REMOTE CONTROLLER
RC5500SR
SURROUND
SURROUND
DISPLAY
PURE
PURE
SETUP
SETUP
DIRECT
DIRECT
SIMPLE
SIMPLE
AUTO
AUTO
HT-EQ
HT-EQ
MENU
MENU
ENTER
MEMORY
CLEAR
T-MODE
EXIT
BAND
MODE
MODE
DISP
MULTI
AUTO
TUNED
ST
V —
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
HEAD PHONE
DOLBY HP MODE
: BYPASS
SURROUND
:
✽✽✽
L LEVEL
: 0dB
R LEVEL
: 0dB
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
AUX1
TUNE/SEARCH
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
6
5
4
9
8
0
7
SURROUND
SURROUND
DISPLAY
DISPLAY
PURE
PURE
SETUP
SETUP
DIRECT
DIRECT
SIMPLE
SIMPLE
AUTO
AUTO
HT-EQ
HT-EQ
MENU
MENU
ENTER
ENTER
MEMORY
MEMORY
CLEAR
CLEAR
T-MODE
T-MODE
EXIT
EXIT
BAND
BAND
MODE
MODE
DISP
MULTI
AUTO
TUNED
ST
V — OFF
NIGHT
PEAK
ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
MT X 6.1
SPKR
B
EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL
S
SR
LFE
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
SURROUND
SURROUND
DISPLAY
DISPLAY
PURE
PURE
SETUP
SETUP
DIRECT
DIRECT
SIMPLE
SIMPLE
AUTO
AUTO
HT-EQ
HT-EQ
MENU
MENU
ENTER
ENTER
MEMORY
MEMORY
CLEAR
CLEAR
T-MODE
T-MODE
EXIT
EXIT
BAND
BAND
MODE
MODE
DISP
MULTI
AUTO
TUNED
ST
V — OFF
NIGHT
PEAK
ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
MT X 6.1
SPKR
B
EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL
S
SR
LFE
06.3.6, 4:28 PM
Page 31