Marantz ZR6001 - Manual (Page 31)

ENGLISH
28
SURROUND MODE
The ZR6001 is equipped with many surround
modes. These are provided to reproduce a variety
of surround sound effects, according to the content
of the source to be played.
The available surround modes may be restricted
depending on the input signal and speaker setup.
AUTO
W h e n t h i s m o d e i s s e l e c t e d , t h e r e c e i v e r
determines whether the digital input signal is Dolby
Digital, Dolby Digital Surround EX, DTS, DTS-ES,
DTS 96/24 or PCM-audio.
Surround EX & DTS-ES will operate for multichannel
source that has a Dolby Digital Surround EX or DTS-
ES auto trigger flag in the digital signal.
When a Dolby Digital or DTS signal is input, the
number of channels for which the corresponding
signal is encoded will be played.
Inputting a Dolby Digital two channel signal with
Dolby surround status automatically subjects that
signal to Pro Logic
II x movie processing before
play.
PCM 96 kHz source material can be played in this
mode.
Notes:
• When you use this mode with certain DVD and
CD players, performing operations such as “Skip”
or “Stop” may momentarily interrupt the output.
• When the signal is not decoded, the mode is
changed to AUTO mode automatically. Refer to
page 27 to confirm the available decoding mode.
2 MODE
(Dolby Digital, Pro Logic IIx MOVIE, Pro Logic
II
x MUSIC, Pro Logic IIx GAME, Pro Logic)
This mode is used with source materials encoded
in Dolby Digital and Dolby Surround.
DOLBY DIGITAL
This mode is enabled when playing source
materials encoded in Dolby Digital.
Playing multichannel encoded 6.1 or 7.1-channel
Dolby Digital sources provides five main audio
channels (left, center, right, surround left and
surround right) and Low Frequency Effect channel.
Dolby Digital EX decoding is not available in this
mode.
Dolby Pro Logic II x brings the excitement of
surround sound to any stereo mix, while making
existing Dolby Surround mixes sound more like
discrete 7.1 channels Surround sound.
Dolby Pro Logic
II x has 3 modes. Please see
below.
Pro Logic II x MOVIE
This mode provides 6.1 or 7.1 channel surround
sound from Dolby Surround encoded stereo movie
sound tracks.
Pro Logic II x MUSIC
This mode provides 6.1 or 7.1 channel surround
sound from conventional stereo sources, analog or
digital, such as CD, Tape, FM, TV, Stereo VCR, etc.
Pro Logic II x GAME
Game mode restores the impact low-frequency
surround effects by routing them to the system’s
subwoofer.
Pro Logic
This mode emulated original Dolby Pro Logic
decoding (3/1 surround) suit for Dolby Surround
encoded stereo movie soundtracks.
Notes:
• Pro Logic IIx mode will decode as Pro Logic II
mode when the SURROUND BACK SPEAKER
is set NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 21)
• Pro Logic IIx mode is available for a 2ch input
signal which is encoded in Dolby Digital or PCM
format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32
kHz, 44.1 kHz or 48 kHz.
TEMPORARILY TURNING OFF
THE SOUND
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the
MUTE
button on the front panel or MUTE button on the
remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“
MUTE” .
Press the MUTE button again to return to normal
operation.
USING THE SLEEP TIMER
To program the ZR6001 for automatic standby,
press the
SLEEP button on the remote.
Each press of the button will increase the time
before shut down in the following sequence.
The sleep time will be shown for a few seconds in
the display on the front panel, and it will count
down until the time has elapsed.
When the programmed sleep time has elapsed,
the unit will automatically turn off.
Note that the SLEEP
indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the
SLEEP
button until the display shows “SLEEP OFF” and
the SLEEP indicator will disappear.
NIGHT MODE
Press the NIGHT button on the remote to turn on
the NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late
at night.
To turn off the Night mode, press the
NIGHT
button again.
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD VCR1 DSS/VCR2 TV
ENTER
AUX1
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO 3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
MENU OSD
ENTER
OFF 10 20 30 40
90 80 70 60 50
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD VCR1 DSS/VCR2 TV
ENTER
AUX1
SURROUND DISPLAY DISPLAY PURE SETUP DIRECT SIMPLE
AUTO HT-EQ MENU ENTER
MEMORY MEMORY CLEAR CLEAR
T-MODE T-MODE EXIT EXIT BAND BAND
MODE
ANALOG DIGITAL DIGITAL SURROUND
AAC PCM L C R SL S SR LFE
06.3.6, 4:28 PM Page 28