MITSUBISHI ELECTRIC WD-52825 - Manual (Page 14)

14 15
IR EMITTER
NetCommand R
DVI
Analog Audio
INPUT-1
AUDIO 2
AUDIO/VIDEO 1
AUDIO
L(MONO) R
INPUT-2
COMPONENT-1
YPbPr (480i/480p/720p/1080i)
Y/G Pb/B Pr/R
COMPONENT-2
YPbPr (480i/480p/720p/1080i)
INPUT-DTV
YPbPr / RGB HV
(480i/480p/720p/1080i)
DTV/
CABLE/
VHF/
UHF
ANT-2
ANT-1
DIGITAL
AUDIO
PC
VGA/SVGA/XGA/
720p
60 Hz
PC-
AUDIO
PC-
INPUT
M-LINK
CONTROL/
RS-232C
HDMI
M-LINK
IEEE1394
INPUT/OUTPUT
L
R
VIDEO S-VIDEO MONITOR
OUTPUT
L
R
V H
CARD
TOP
C
ab
leC
AR
D
SL
O
T
TM
1.
2.
3.
4.
5.
6. 7.
8.
9.
10.
11.
MAIN
AUX
12.
Back Panel
1. Antenna (ANT-1 MAIN, ANT-2 AUX)
ANT-1 MAIN and ANT-2 AUX can each receive both
digital and analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable channels.
Your primary viewing signal source should be connected
to ANT-1 MAIN. ANT-1 MAIN must be used to view
premium subscription cable TV service authorized by the
CableCARD™ access card. The CableCARD access card
is provided by your local cable company. ANT-2 AUX can
receive over-the-air or non-scrambled cable signals.
2. CableCARD™ Slot
The CableCARD access card provided by your cable TV
service provider is inserted into this slot. The top of the
card should face in the direction the CARD TOP arrow
indicates.
CableCARD is a nationwide standard system that allows
your local cable TV provider to supply you with an
access card customized to your account. This card
allows the TV to receive, decode and unscramble the
premium digital channels included in your cable TV
subscription without the use of a cable box. See page
20 for additional CableCARD information and activation
instructions.
If your cable company is not currently offering
CableCARD access cards, you will need to use a cable
box provided and authorized by your local cable company
to view scrambled channels.
3. Input-DTV
YPbPr/RGB HV (480i/480p/720p/1080i)
This input is used to connect an external DTV receiver,
and can be configured for YPbPr or RGB plus H&V signal
types. Please see Appendix B for signal compatibility.
4. Component-1, -2 Inputs
YPbPr (480i/480p/720p/1080i)
These inputs can be used for the connection of devices
with component video outputs, such as a DVD player,
external HDTV receiver or compatible video game system.
Please see Appendix B for signal compatibility.
5. Input-1, -2; Monitor Output
(Audio/Video 1, Audio 2)
Input 1 and 2 can be used for the connection of a VCR,
Super VHS (S-VHS) VCR, DVD player, standard satellite
receiver or other A/V device to the TV. Please note that
if S-VIDEO and VIDEO are available for the input, you
must choose to connect only one. They cannot both be
connected at the same time.
The Monitor Output sends the TV audio and video signals
from the antennas or inputs to an A/V receiver or other
analog A/V equipment such as a VCR. Digital channels
and IEEE 1394 signals will be down converted to analog
signals compatible with traditional VCRs. Digital
channels or IEEE 1394 signals may be output with copy
protection or may display no video signals if they have
copy restrictions. There will be only audio and no