MITSUBISHI ELECTRIC WD-52825 - Manual (Page 24)

24 25
A/V Receiver or Stereo System
Figure 7
A digital audio cable and stereo audio cables are required. The
digital audio cable is provided. The stereo audio cables are not
included with the TV.
1. Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
To connect a digital A/V receiver with Dolby®
Digital surround sound:
2. Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
Check A/V receiver’s Owner’s Guide for information
concerning the use of the digital input and switching
between the digital sound and analog stereo sound
from the TV.
IN IN IN IN IN IN IN IN OUT OUT OUT OUT
AUX CD TAPE 1 TAPE 2 VCR 1 VCR 2 TV DVD
MONITOR VCR 1 VCR 2 TV DVD
MONITOR VCR 1 VCR 2 TV DVD OUT
OUT
IN
IN
IN
IN
IN
IN
IN
IN
OUT OUT
OUT OUT
CENTER
SUB
WOOFER
FRONT SUR.
REC SOURCE
LINE OUT PRE OUT SURROUND SPEAKERS ���� MIN.�
FRONT SPEAKERS-A ���� MIN.� FRONT SPEAKERS-B ���� MIN.� CENTER
��� MIN.�
L L
L L
R
L
R
R
R
THIS DEVICE COMPLIES WITH PART 15 OF THE
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING
CORPORATION. "DOLBY", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE
TRADEMARKS OF DOLBY LABORATORIES CORPORATION.
COPYRIGHT 1992 DOLBY LABORATORIES, INC. ALL RIGHTS
RESERVED
INPUT-1 (OPTICAL)
INPUT-2 (COAXIAL)
INPUT-3 (COAXIAL)
DIGITAL AUDIO
SWITCHED UNSWITCHED
AC 120V - 60Hz TOTAL 100W, 0.9A MAX AC OUTLETS
MITSUBISHI
AUDIO/VIDEO RECEIVER
MODEL M-VR1000
POWER SUPPLY
POWER CONSUMPTION 120V-60Hz
552W, 732VA
DISTRIBUTED BY MITSUBISHI CONSUMER ELECTRONICS AMERICA INC. 6100 ATLANTIC BLVD MADE IN JAPAN NORCROSS, GA 30071-1305 FABRIQUE EN JAPAN
! AVIS
RISQUE DE CHOC ELECTRONQUE NE PAS ENLEVER RISK OF ELECTRIC SHOCK DO NOT OPEN
ANTENNA
75 �
300 �
FM
AM
GND
ATUO STANDBY
ON OFF �
�
S-VIDEO
VIDEO
AUDIO
WARNING
A/V Receiver Rear Panel
Use only if
connecting
a Dolby Digital
A/V Receiver
2.
Red White
1.
IR EMITTER
NetCommand R
INPUT-1
AUDIO 2
AUDIO/VIDEO 1
AUDIO
L(MONO) R
INPUT-2
DIGITAL AUDIO
PC VGA/SVGA/XGA/ 720p 60 Hz
PC- AUDIO
PC- INPUT
M-LINK CONTROL/ RS-232C
HDMI M-LINK
IEEE1394 INPUT/OUTPUT
VIDEO S-VIDEO MONITOR OUTPUT
L
R
DTV/ CABLE/ VHF/ UHF
ANT-2 AUX
ANT-1 MAIN
AUDIO
L(MONO) R
TV back panel section
AUDIO 2
DIGITAL AUDIO
MONITOR OUTPUT
IN
TV
L
R
INPUT-2 (COAXIAL)
1. Red
White
2.
L
R
DVI Analog Audio
Figure 7. Connecting an A/V receiver
Connecting an A/V Receiver or Stereo System or
a Satellite Receiver or Other Device with S-Video
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO,
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel.
Note: Refer to the Satellite Receiver Owner’s
Guide for Dish Antenna connections.
IR EMITTER
NetCommand R
INPUT-1
AUDIO 2
AUDIO/VIDEO 1
AUDIO
L(MONO) R
INPUT-2
DIGITAL
AUDIO
PC
VGA/SVGA/XGA/
720p
60 Hz
PC-
AUDIO
PC-
INPUT
M-LINK
CONTROL/
RS-232C
HDMI
M-LINK
IEEE1394
INPUT/OUTPUT
VIDEO S-VIDEO MONITOR
OUTPUT
L
R
DTV/
CABLE/
VHF/
UHF
ANT-2
AUX
ANT-1
MAIN
AUDIO
L(MONO) R
INPUT-2
2.
TV back panel section
1.
(Y/C) L
R
L
R
1 2
VIDEO OUT AUDIO OUT AUDIO IN
Any S-Video Device
White
Red
1.
2.
Red White
DVI
Analog Audio L
R
Note: NetCommand® will asssume you
connected your Satellite Receiver to Input-2.
If you add a second Satellite Receiver or use
any other inputs for your Satellite Receiver,
this change must match in the NetCommand
system. See Editing NetCommand Setup in
Chapter 3 for more information.
Figure 8. Connecting a Satellite Receiver with S-Video