Marantz CR601 - Manual (Page 28)

24
ENGLISH
7 Muting the CR601
Use this function to mute the output of the CR601
temporarily.
1. Press the MUTE button m .
• The output is muted and “ Muting ” flashes on
the display.
2. To unmute the CR601, press the MUTE button
m again, or adjust VOLUME 5∞ button ¤7 .
• The output is unmuted and “ Muting ” goes off.
Note
The Mute function is cancelled when the CR601
is set to Standby.
7 Adjusting the Bass & Treble
Use the Bass and Treble functions to adjust the
tone of the sound to your personal preference.
1. Press the DIRECT button y or ¤0 to select
“ Tone Direct Off ”.
2. Use the Tone control Bass knob !0 or the
Tone control TREBLE knob o to adjust the
bass or treble.
7 Using Direct Mode
In Direct mode, the bass and treble tone circuits
are bypassed, creating a shorter signal path for a
purer sound.
1. Press the DIRECT button y or ¤0 to select
“ Tone Direct On ”.
2. To turn off Direct mode, press the DIRECT
button y or ¤0 again to select “ Tone Direct Off ”.
OTHER OPERATION
SETTING THE CLOCK
7 Present time setting
• To operate the timer program, you must set the
present time.
The clock time can be set 12-hour or 24-hour
system.
The clock displays “
SUNDAY ” “ 12H SYSTEM ”
“ 0:00AM ” at initial.
1. Press the CLOCK CALL button ‹1 . Then the
“ CLOCK 0:00AM ” is displayed.
2. Press the ENTER button b , the day of the
week flashes.
3. Press the 5 or ∞ button c to select a day.
4. Press the ENTER button b , “ 12H SYSTEM ” is
flashes.
If you want to select 24H SYSTEM, either press
the
5 or ∞ button c .
5. Press the ENTER button b to set the desired
system. The hour digit flashes.
6. Press the 5 or ∞ button c to set the hours and
press the ENTER button b . The minute digit
flashes.
555
55
555
7. Press the 5 or ∞ button c to set the minutes,
and press the ENTER button b . The display
flashes.
8. Press the ENTER button b to confirm the
actual time. The clock now starts.
• In the event of a power failure or when the AC
mains cord is disconnected. You must reset
the clock.
7 Displaying present time
1. A present time can be displayed for 5 seconds
by pressing the
CLOCK CALL button ‹1 .
7 Displaying present time in
Standby mode
If you want to be displayed the present time in
Standby mode, press the
CLOCK CALL button ‹1
in Standby mode.
Note
Setting the CR601 to display the present time
will slightly increase the power consumption in
Standby mode.
555 555
55 5 5 5
STANDBY STANDBY PHONES PHONES POWER ON / STANDBY POWER ON / STANDBY
CD RECEIVER CR601 CD RECEIVER CR601
PUSH TO ENTER PUSH TO ENTER VOLUME VOLUME
TREBLE TREBLE BASS BASS
INPUT INPUT MENU MENU DIRECT DIRECT
y o !5 !0
MEMO
AUTO TUNE SLEEP SHIFT DIRECT
AM FM DAB
--/---
MUTE
DISPLAY
VOL
INPUT
DIMM
VOL
10/0
9
8 7
6
5 4
3
2 1
INPUT
MODE
TUNING PRESET
ENTER
CLOCK CALL
MENU
CLEAR
TIMER
REPEAT
REMOTE CONTROLLER RC601CR REMOTE CONTROLLER RC601CR REMOTE CONTROLLER RC601CR
¤0
m ¤7
b
¤3
¤2
‹1
c