Integra DTR-8.2 - Manual (Page 56)

56
+
–
CH
VOL
MUTE
CONT
+
–
LIGHT
Phones Zone 2 Level Stereo Surround THX DSP Rec Out Zone 2 Off Dimmer FM Mode Memory Setup
Clear
Enter Return Video 5/Video Cam Input Tuning Preset
S Video Audio Video L R Didital
Master Volume Standby/On
Power
On O f f
Video 1 Video 3 Tape FM AM Phono CD DVD Video 2 Video 4 Video 5
Zone 2 ( ) GRN Rec ( ) RED Pure Audio psampling U
Standby
Display Audio Selector
Direct/ Pure Audio
Off
Zone 2
Zone 2 Level /
VOL
CH +/–
ON
Enjoying music in the remote zone
Playing music using the buttons on the DTR-8.2
1. Press the Zone 2 button on the DTR-8.2.
2. Select a source.
After pressing the Zone 2 button, you must press an input source
button within 5 seconds. The Zone 2 indicator lights.
ZONE 2 indicator
To select the same source for the remote zone that is selected
for the main zone, press the Zone 2 button again until
“Zone2Sel:SOURCE” appears in the display.
Ex.: When the CD button is pressed.
When “Zone2Sel:Off” is displayed, the output to the remote
zone is turned off.
Adjusting the volume for the remote zone
When the remote zone (Zone 2) speakers are connected to the
SURR BACK/ZONE 2 SPEAKERS terminals, or to an amplifier
connected to the SURR BACK/ZONE 2 PRE OUT terminals,
adjust the volume as shown below.
Press the Zone 2 Level / buttons on the front panel.
Note:
When the remote zone (Zone 2) speakers are connected to the pre-
main amplifier that is connected to the ZONE 2 terminal of the DTR-
8.2, adjust the volume for the remote zone at the pre-main amplifier.
Selecting an input source using the remote
controller
When using the remote controller, select Zone 2 in the Home menu
to display the Zone 2 operation menu.
Turning on the Zone 2 and putting it in the standby state
when the DTR-8.2 is in the standby state:
Tap the ON button.
Selecting an input source:
Press an input source button.
If you select Tuner of the input selector buttons, you can select a
preset channel using the CH +/– buttons.
Adjusting the volume:
Press the VOL / buttons on the remote controller.
Input source buttons
Input
selector
buttons
Notes:
• If a sleep time is set with the Sleep button, it will also work for
the remote zone.
• If the source for the main zone is selected as the source for the
remote zone and the source for the main zone is changed, then
the source for the remote zone will change as well.
• The Zone 2 terminal is an analog output. Digital signals are not
output. If no sound is heard from the selected input source, check
if the component is connected to the analog inputs.
• If the Rec Out button is pressed in the main room while someone
is using the system in the remote zone, the Zone 2 function will
be deactivated and the source will turn off in the remote zone.
• If you select FM (or AM) with the input source buttons when the
source for the remote zone (Zone 2) is set to AM (or FM), the
output for the remote zone also changes to AM (or FM).
• 7.1-channel playback in the main room is disabled if the
Powered Zone 2 setting of the Speaker Config sub-menu is set to
“Activated.”
• When you are using the remote zone (Zone 2), system
operation will not work.
• When you are using the remote zone (Zone 2), the Pure Audio
setting will not work.
• When you are not using the remote zone (Zone 2), press the Zone
2 button and then press the Off button to turn off the Zone 2
indicator.
Note:
Each time you press one of the Zone 2 buttons on the remote
controller, the STANDBY indicator on the DTR-8.2 flashes for five
seconds. During this time, you will not be able to perform operations
in the main zone using the remote controller.
VOL
+
–
CH