I-O Display Systems Basic I/O Product - Manual (Page 54)

Introduction 1
1-8(Vol.2)
Available I/O Modules
ANALOG INPUTS, 12 BIT ANALOG OUTPUTS, 12 BIT
Frequency Voltage
I F10K-B Input 300Hz-10KHz OV1 Output 0-1V, self-sourcing
IF2.5K-L Input 0-2.5KHz OV5 Output 0-5V, self-sourcing
IF5K-l Input 0-5KHz OV10 Output 0-10V, self-sourcing
IF10K-L Input 0-10KHz Current
Voltage OI420 Output 4-20mA, self-sourcing To 275
Ohm load
IV25M Input 0-25mV
IV50M Input 0-50mV DIGITAL INPUTS
IV100M Input 0-100mV AC
IV1 Input 0-1V IAC5 Input 90-140Vac
IV5 Input 0-5V IAC5A Input 180-280Vac
IV5B Input Bipolar +/-5V DC
IV10 Input 0-10V IDC5D Input 3-32Vdc Fast, >500Hz
IV10B Input Bipolar +/-10V IDC5S * Input Dry Contact Sense, Built-in Isolated
Voltage Source
IVAC Input 28-140Vac IDC5NP Input 10-32 Vdc, 15-32Vac Non-
Polarized.
IVAC-A Input 56-280Vac
Current DIGITAL OUTPUTS
II420 Input 4-20mAdc AC
IIAC5 Input 0-5Aac OAC5 Output 12-140Vac, 3.5A
Thermocouple OAC5A Output 24-280Vac, N.C.(Normally Closed)
ITCE Type E 0 To 435° C OAC5J Output 20-280Vac, 6.0A
ITCJ Type J 0 To 700° C DC
ITCJ-1 Type J -80 To 750 °C ODC5 Output 5-60Vdc, 3.5A
ITCK Type K -100 To 924° C ODC5A Output 4-200Vdc, 1.0A
ITCK-1 Type K -110 To 1250 °C ODC5R Electro-Mechanical 0.5A Relay Form A,
Normally )
ITCR Type R 0 To 960° C IDC5Z* Input +/-200mV, 0-10KHz Digital**
ITCR-1 Type R 0 To 1760 °C SPS-1* Sensor Power Supply 18-24 Vdc, 30mA
ITCS Type S 0 To 1034° C TI01 Digital Input/ Output Test Module with
Field Switch and LED
ITCS-1 Type S 0 To 1760° C
ITCT Type T -200 To 224 °C
ITCT-1 Type T -120 To 400° C
ITCT-2 Type T 0 To 150 °C
SPECIAL PURPOSE SUPPORT PRODUCTS
RTD Fuses
ITR10 10 Ohm Cu -55 To 150 °C FM-06 Fuse assembly, 0.062A 100 mA for
modules marked with an *
ITR100 100 Ohm Pt -55 To 350 °C FM-1 Fuse assembly, 1.0A
ITR100-1 100 Ohm Pt 0 To 100 C FM-3 Fuse assembly , 3.0A
Type 590 Temperature Sensor FM-5 Fuse assembly, 5.0A
ITP590 -188.4 To 150 °C
ITP590-1 -50.0 To 150 °C
* When selecting a power supply for the system assume 25mA for standard digital modules and 100mA for modules
marked with an *
** The IDC5Z module is used for low-level signals and will pass signals at the rate of 10kHz
The BASIC I/O AD
however, is limited by communications baudrate.