IBM Switch 9077 - Manual (Page 302)

284 IBM 9077 SP Switch Router: Get Connected to the SP Switch
#gt020 0.0.0.0 255.255.255.0 - mtu 65520
gt030 192.168.14.4 255.255.255.128 - mtu 65520
#gt040 192.168.14.129 255.255.255.128 - mtu 65520
gt050 192.168.14.129 255.255.255.128 - mtu 65520
#gt060 0.0.0.0 255.255.255.0 - mtu 65520
#gt070 0.0.0.0 255.255.255.0 - mtu 65520
#gt080 0.0.0.0 255.255.255.0 - mtu 65520
#gt090 0.0.0.0 255.255.255.0 - mtu 65520
#gt0a0 0.0.0.0 255.255.255.0 - mtu 65520
#gt0b0 0.0.0.0 255.255.255.0 - mtu 65520
#gt0c0 0.0.0.0 255.255.255.0 - mtu 65520
#gt0d0 192.168.13.16 255.255.255.0 - mtu 65520
#gt0e0 0.0.0.0 255.255.255.0 - mtu 65520
#gt0f0 0.0.0.0 255.255.255.0 - mtu 65520
de0 192.168.4.4 255.255.255.0
#ga010 10.1.1.1 255.255.255.0 - mtu 9180
#ga0180 10.1.2.1 255.255.255.0 10.1.2.1
bg1 10.1.1.1 255.255.255.0 - mtu 9180
# gf000 10.2.1.15 255.255.255.0 - mtu 4352
# gf001 10.3.1.16 255.255.255.0 - mtu 4352
# gf002 10.4.1.17 255.255.255.0 - mtu 4352
# gf003 10.5.1.18 255.255.255.0 - mtu 4352
bg0 10.10.1.13 255.255.255.0 - mtu 4352
ge070 10.20.30.1 255.255.255.0 - mtu 1500
#ge071 192.168.4.71 255.255.255.0 - mtu 1500
#ge072 192.168.4.72 255.255.255.0 - mtu 1500
#ge073 192.168.4.73 255.255.255.0 - mtu 1500
#ge074 192.168.4.74 255.255.255.0 - mtu 1500
#ge075 192.168.4.75 255.255.255.0 - mtu 1500
#ge076 192.168.4.76 255.255.255.0 - mtu 1500
#ge077 192.168.4.77 255.255.255.0 - mtu 1500
gh080 10.50.1.1 255.255.255.0 - mtu 65280
# ga020 10.20.30.1 255.255.255.0 - mtu 9180
B.11 /etc/grlamap.conf
This file contains the mapping of logical addresses to destination portcards
for HIPPI interfaces. We used this file in Section 7.3, “HIPPI Backbone
Connection” on page 227.
# NetStar $Id: grlamap.conf,v 1.1 1995/02/09 20:29:27 scotth Exp $
#
################################################################################
#
# There are 3 fields to determine how logical addresses get
# mapped to destination portcards for each hippi portcard.
#
# The first field is a comma separated list which determines the
# portcard on which the other 2 fields will apply.
# Ranges are allowed. i.e., 1,4-9,15 == 1,4,5,6,7,8,9,15
# ’*’ signifies that all portcards get this mapping.
#
# The second field is a comma separated list of logical addresses being mapped.
# Ranges are allowed.
# values: 0 - 4095 inclusive, ’*’ signifies the default (i.e., all LAs).
#
# The third field is a comma separated list of destination port cards.
# Only the first 4 values will be taken as valid, any extra values will
# be flagged invalid, a message will be printed to gr.console & grlamap will