JVC TK-C655 - Manual (Page 10)

10
1
TO CAMERA TO CAMERA DATA I / O RX RX+ RX RX- TX TX+ TX- COM COM 1 2 3 4 5 6 7 8 COM COM 9/1 10/2 10/2 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 16/8 16/8 COM COM COM COM COM COM CAMERA CAMERA SW SW UNIT ALARM AUTO
4 3 1 2 8 7 5 6
2 3 4 5 6 7 8
1
MONITOR MONITOR
OUTPUT OUTPUT
MONITOR MONITOR
SERIAL-2 SERIAL-1
VIDEO INPUT VIDEO INPUT
VIDEO OUTPUT
OUTPUT OUTPUT
2
1 ON 2 3 4 5 6 7 8
POWER
OFF ON
AC INPUT
MONITOR
OUTPUT 1
TO
CAMERA
Remote control unit
RM-P2580
Control signal cable
Coaxial cable
AC 24 V
power supply
( CAUTION
AC 24 V
power supply
( CAUTION
AC 24 V
power supply
( CAUTION
Monitor
Camera 1
Camera 2
Camera 8
TK-C655/
TK-C676
TK-C655/
TK-C676
TK-C655/
TK-C676
MACHINE ID: 01
Switch 8: OFF
(RX TERM)
MACHINE ID: 02
Switch 8: OFF
(RX TERM)
MACHINE ID: 08
Switch 8: ON
(RX TERM)
TX + A
TX – B
RX + C
RX – D
TX +
Camera 1
CONTROL terminals
Camera 2
CONTROL
terminals
Camera 3
CONTROL
terminals
RX + A
RX – B
TX + C
TX – D
RM-P2580
terminal
A
TX – B
RX + C
RX – D
TX + A
TX – B
RX + C
RX – D
Connection of the control signal cable
(A twisted pair cable is recommended.)
Power cable
Control signal cable
To AC 24V power supply
( CAUTION
To the TO CAMERA connector of the
RM-P2580 and to the next camera
Coaxial cable
To the CAMERA INPUT connector
of the RM-P2580
Duplex display ID No. display
L PROCESS<< >> I I N T I A
: - - I - - PAN
: - - I - - T I LT
DUPLEX I D - 01 ROT >P C O OL
Camera 1 monitor display
at power ON
(ID check procedure
☞
P. 15)
Switch 1 :
Switch 2 :
Switch 4 : ON
Switch 5 : OFF
Switch 7 : Invalid (Set to OFF)
Switch 8 :
Figure of 1
Figure of 10
Set it to the same number as the
VIDEO INPUT terminal of the RM-
P2580.
(Example) Camera 1:
Set the figure of 10 to “0” and
figure of 1 to “1”.
Set to ON only for the
camera connected at
the end of the control
signal cable.
Set to OFF for all
other cameras.
Machine ID
0 9 8 7 6 5 4 3 2 1
0 9 8 7 6 5 4 3 2 1
1 2 3 4 6 7 8 5
O F F
Invalid (Set to OFF.)
A Multi-Drop Communication System
Ⅵ A system that employs the RM-P2580 as the controller
The following figure shows a system that can accommodate up to eight cameras. (100 positions can be preset per camera.)
Observe the following points when connecting compo-
nents together:
• Turn all the components off before proceeding.
• Read the instruction manuals of all components before pro-
ceeding.
• For the types and lengths of connection cables, see “Cable
Connections” on page 16.
• Do not connect the control signal cables in a loop.
Cable connections
☞
P. 16
(Terminal side of Ceiling Mount)
Switch settings
☞
P. 14
(Setting switches are on the side of the Ceiling Mount)
Each terminal on the camera and the RM-
P2580 is marked
A
⅜
, B
⅜
, C
⅜
or D
⅜
. In order
to facilitate understanding and to avoid
connection mistakes, it is recommended
to connect the terminals carrying the
same marks.
CAUTIONS
●
The AC 24 V power supply must be isolated from the pri-
mary line. (ISOLATED POWER ONLY)
●
In order to prevent an excessive current flow through the
power supply wire or camera due to a short circuit, a fuse
must be installed in the power supply line.
Connections & Installation