Document Outline

• Safety Information
  • Introduction
  • Installation Safeguards
  • Heat Safeguards
  • Light Safeguards
  • Electrical Safeguards
    • Power Supply
  • Fluid Safeguards
  • Ventilation and Foreign Object Retrieval
• 1.0 Introduction
  • 1.1Safety
  • 1.2 Updates
  • 1.3Tool List
  • 1.4Acronyms Used in this Manual
• BCH2SYDS.pdf
  • 2.0 System Description
    • Contents
    • 2.1 Introduction
    • 2.2 Optical System
      • 2.2.1 Image Path
      • 2.2.2 Arc Lamp Light Path
    • 2.3 Electronics System
      • 2.3.1 General Description
      • Figure 2-2. Model 200 System Block Diagram
      • 2.3.2 Power Supplies
      • 2.3.3 Video Input Cards
      • Standard RGB Video Input Card (RGB_VIC)
      • Quad Input RGB VIC
      • HDTV YPbPr VIC
      • Quad Standard Decoder VIC
      • 2.3.4 Video Processor PCB
      • 2.3.5 Video Amplifier
      • 2.3.6 System Controller PCB
      • 2.3.7 Raster Timing Generator PCB
      • 2.3.8 Horizontal/Vertical Deflection PCB
      • 2.3.9 Convergence/Deflection PCB
      • 2.3.10 Scan Reversal Board
      • 2.3.11 Backplane PCB
    • 2.4 Image Light Amplifier Technology
• CCH3SADJ.pdf
  • 3.0 Service Adjustments
    • Contents
    • 3.1Arc Lamp Focus and Alignment
    • 3.2Arc Lamp Current Setting
    • 3.3Electronic Module Tilt-up
    • 3.4ILA® Back Focus
    • 3.5CRT Mechanical Focus
    • 3.6CRT Rotation
    • 3.7CRT Electronic Focus
    • 3.8ILA® Overlap
    • 3.9Front/Rear or Inverted Projection Jumper Settings
      • 3.9.1Front/Rear Jumper Setting (Horizontal Reverse)
      • 3.9.2Inverted Vertical Jumper Setting
    • 3.10Vertical and Horizontal Size Settings
    • 3.11Software Updating
    • 3.12Cleaning Lenses, ILA® Assemblies and Mirrors
• DCH4MAIN.pdf
  • 4.0 Maintenance (Removal/Replacement)
    • Contents
    • 4.1 Introduction
    • 4.2 Projector Covers
    • 4.3 Air Filters
    • 4.4 Arc Lamp Assembly
    • 4.5 Arc Lamp Power Supply
    • 4.6 Low Voltage Power Supply
    • 4.7 High Voltage Power Supply
    • 4.8 Raster Timing, System Controller, Video Processor PCBs
      • All electrical connections to the Raster Timing Generator, System Controller, and Video Processor boards are routed through the backplane board. There are no connectors to remove.
      • NOTE: To remove connectors on the printed circuit boards below, push the connector in slightly, then squeeze the tab and pull the connector out.
    • 4.9 Convergence/Deflection PCB.
    • 4.10 Horizontal/Vertical Deflection PCB
    • 
      
    • 4.11 Video Input Cards (VICs)
    • 4.12 Video Amplifier PCB
    • 4.13 Scan Reversal PCB
    • 4.14 CRT/Yoke Assembly
    • 4.15 ILA® Assembly
    • 4.16 Relay Lens
    • 4.17 Projection Lens
    • 4.18 Prism Assembly
• ECH5TSHO.pdf
  • 5.0 Troubleshooting
    • Contents
    • 5.1 Status LEDs
    • 5.2 Error Codes
    • 5.3. Troubleshooting Guide
• HGLOSSRY.pdf
  • Glossary Of Terms