JVC RD-MD5 - Manual (Page 21)

18
■
2. Press the MD 6 button and then 7 button
to set the function to MD.
The track numbers and total playback time are displayed.
■
3. Press the EDIT button until "ERASE ?" is
displayed.
Each time you press the button, the display changes as follows.
Current display
= DIVIDE = JOIN = MOVE = ERASE =
ALL ERASE = (back to the beginning)
■
4. Press the SET button.
■
5. Select the track number to be erased.
Press the 4 or ¢ button or turn the JOG dial to select the
track.
■
6. Press the SET button.
■
7. Press the ENTER button.
The selected track is erased and the number of tracks decreases
by 1. The new total track number and the total playback time ap-
pear on the display.
■
8. Press the 0 MD button to complete editing.
The MD is ejected after “UTOCwriting” is displayed.
•
You can also complete editing operation by pressing
the
button to turn off the power.
To cancel the operation, press the CANCEL button in step 4, 5,
or 6 until the display returns to the original display before editing
the track.
Note: While “UTOCwriting” is displayed, do not disconnect the
power cord or subject the Unit to the vibration to avoid in-
correct recording.
■
Use the Unit to carry out this function.
■
1. Insert an MD to be edited with its label side
up.
■
2. Press the MD 6 button and then 7 button
to set the function to MD.
The track numbers and total playback time are displayed.
■
3. Press the EDIT button until "ALL ERASE ?"
is displayed.
Each time you press the button, the display changes as follows.
Current display
=DIVIDE=JOIN=MOVE=ERASE=ALL
ERASE =(back to the beginning)
■
4. Press the SET button.
■
5. Press the ENTER button.
All the tracks in the MD are erased and "BLANK DISC" is kept
displayed.
■
6. Press the 0MD button to complete editing.
The MD is ejected after "UTOCwriting" is displayed.
•
You can also complete editing operation by pressing the
button to turn off the power.
To cancel the all erasing, press the CANCEL button in step 4.
Note: While "UTOCwriting" is displayed, do not disconnect the
power cord or subject the Unit to the vibration to avoid in-
correct recording.
You can give a disc title to the MD and a track title to the tracks in
the MD. Any title name can be given up to 32 characters using the
provided character sets.
The disc title you have given will be displayed in the following cases.
•
When you insert the MD while the function is set to MD.
• When you press the MD 6 button and then 7 button to set the
function to MD.
Once you have given the title to the tracks, the track title will be dis-
played before playing the track.
■
Since the procedure to give title is the same as for the disc title
and track title except for step 4, both functions are explained to-
gether here.
■
Use the Unit to carry out these functions.
■
1. Insert an MD to be edited with its label side
up.
■
2. Press the MD 6 button and then 7 button
to set the function to MD.
The total track numbers and total playback time are displayed.
■
3. Press the TITLE button until "DISC TITLE ?/
TITLE ? (for track title)" is displayed.
Each time you press the button, the display changes as follows.
Current display
=DISC TITLE=TITLE=(back to the begin-
ning)
■
4. Press the SET button.
• For DISC TITLE:
• For TITLE (Track Title):
1 Select the track number to be given the title by pressing the
4 or ¢ button or turning the JOG dial.
2 Press the SET button.
Erasing all the Tracks
(ALL ERASE Function)
Track to be erased.
Giving Titles to MD (DISC TI-
TLE/TITLE Function)
Cursor
Cursor
Title name area Characters to be input
Alternates
Track to be given the title
Cursor
Title name area Characters to be input
Alternates
Cursor
RD-MD5(B)-e.fm Page 18 Wednesday, December 2, 1998 11:40 AM