JVC BR-DV6000 - Manual (Page 46)

46
BR-DV6000
PROFESSIONAL MENU RESET A.DUB
EJECT
COUNTER AUDIO INPUT SELECT MONITOR OUTPUT REMOTE
LOCAL
CTL L
MIX
R
CH-1/2
MIX
CH-3/4
DV
LINE
Y/C (CPN)
TC
UB
REW STOP FF
REC
OPERATE
PLAY PAUSE DISP
SET SEARCH+
BLANK CUE UP HOLD
PHONES REC LEVEL
CH-1/3 CH-2/4
MIC
SEARCH–
Mini
VIDEO LINE
IN
OUT
MONITOR OUT
DC12V
DV IN/OUT
IN OUT OFF
AUDIO
REMOTE2
IN B-Y R-Y
SYNC IN TIME CODE IN OUT
Y
COMPONENT
OUT CH 1/3 CH 2/4
IN
OUT
MONITOR
OUT REMOTE1 TIMER
REC PLAY
SERIAL REMOTE SIGNAL GND
Y/C
SERIAL OUT SERIAL IN
———R E MO T E [ 1 / 2 ] ———
R E MO T E S E L 9 P O N
R E MO T E S E L S E R O N
R E MO T E S E L D V O N
R E MO T E S E L J V C O N
R E MO T E S E L N E T O N
L O C A L F U N C T I O N S T P + E J T
P R E R O L L 7 S E C
N E X T P A G E
P A G E B A C K
——— R E M O T E [ 2 / 2 ] ———
R E M F F / R E W M O D E F F / R E W
R E M S T O P S E L . E E
P B S T A R T D E L A Y O F
S Y N C H R O N I Z A T I O N O N
C O N T R O L L E R S E L T Y P E 1
F O O T S W O F F
P A G E B A C K
: Connection :
The serial remote controller (RM-G30, sold separately) can be con-
nected to the SERIAL REMOTE IN terminal located on the rear panel
of BR-DV6000.
The input signals of the SERIAL REMOTE IN terminal can be through-
output from the SERIAL REMOTE OUT terminal. (Only with OPER-
ATE ON)
: Setting :
Ⅵ To use the SERIAL IN terminal, set REMOTE SEL SER
in the REMOTE (1/2) Menu screen to ON or LOC+REM.
Then, set the REMOTE/LOCAL switch on the front panel
accordingly.
● REMOTE SEL SER
ON : When the REMOTE/LOCAL switch is set to REMOTE,
operations can be performed via the SERIAL REMOTE
IN terminal.
LOC+REM: With the REMOTE/LOCAL switch is set either way,
operations can be performed via the SERIAL REMOTE
IN terminal. With this setting, the buttons and switches
of the unit can be used too.
Ⅵ Set FOOT SW in the REMOTE (2/2) Menu screen ac-
cording to how the serial remote terminal is used.
OFF : Set to OFF when the serial remote controller is used.
The footswitch cannot be used.
L EDGE : Recording and recording pause is switched at the LOW
edge of the footswitch signal.
H EDGE : Recording and recording pause is switched at the
HIGH edge of the footswitch signal.
L LEVEL : Recording is performed at the LOW edge and paused
at the HIGH edge of the footswitch signal.
: Operation :
Before using the foot switch, set BR-DV6000 to the RECORDING or
RECORDING PAUSE mode using the relevant buttons of the unit.
(Only with L EDGE and H EDGE)
Memo
● The foot switch can only be used to switch between RECORDING
ON and OFF.
● The foot switch can be operated regardless of the setting of the
REMOTE/LOCAL switch.
Memo
● Besides recording, the
serial remote controller
can perform other func-
tions.
● If the REMOTE SEL SER
is set to ON, unit buttons
that can be operated can
be selected from LOCAL
FUNCTION in the RE-
MOTE (1/2) Menu
screen.
Recording can be turned ON/OFF with a serial remote controller or foot switch connected to the
SERIAL REMOTE IN terminal located at the rear panel of BR-DV6000.
REMOTE/LOCAL switch
• Serial remote controller: RM-G30
• Foot switch
REMOTE (1/2) Menu screen
REMOTE (2/2) Menu screen
RECORDING
– Recording with serial remote terminals –
Foot switch
Serial IN
H
400ms L
Min
Signal
terminal
DV6000U_28-051_Eng.p65e 06/03/03, 11:39 PM 46