Sony TA-F5000 - Manual (Page 11)

11 GB
Additional Information
Troubleshooting
If you’ve experience any of the following difficulties while
using the amplifier, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
No sound output.
/ Connect the audio connecting cords firmly.
/ Connect the amplifier and other audio components
correctly.
/ Turn INPUT SELECTOR to the appropriate programme
source.
No audio from one channel or unbalanced speaker
output.
/ Turn BALANCE to adjust the balance.
/ Check the speaker and input connections of silent
channel.
Sudden loss of audio and the POWER indicator lights up
red.
/ The speaker cords have been shorted. Make sure they are
connected correctly.
Weak bass or treble.
/ Adjust the BASS or TREBLE control.
/ Turn INPUT SELECTOR to select the appropriate
cartridge type (see page 8).
/ Change speaker positions or room conditions to eliminate
obstructions in sound path.
Distorted sound.
/ Improperly selected input signal.
/ Insufficient input capacity of speakers. Lower the
volume.
Lack of bass or ambiguity in instrument positions.
/ Speaker cord and terminal polarity are reversed.
Reconnect the cords with correct polarity.
Hum or noise.
/ Ground the turntable system (see page 5).
/ Connect the audio connecting cords firmly.
/ The amplifier is picking up interference from a TV set.
Move the amplifier away from the TV set or turn the TV
set off.
Cannot record.
/ Turn INPUT SELECTOR to the appropriate programme
source.
Specifications
Power Amplifier: Pure-complementary SEPP MOS FET
power amplifier with all stages directly coupled
Preamplifier: Low-noise, high-gain equalizer amplifier +
MC head amplifier
Power section: Large-capacity power supply advanced STD
Additional Information
System
Rated output
(at 4 ohms)
Speaker impedance
Total harmonic
distortion
Damping factor
Frequency response
Input sensitivity and
impedance
S/N
Output level /
impedance
Phones output
Tone controls
Power requirements
Power consumption
Dimensions (approx.)
(w/h/d)
Mass (approx.)
45 W + 45W (DIN)
35 W + 35W (RMS, 20 Hz to 20 kHz)
4 to 16 ohms
0.008% (at 8 ohms, 10 W output)
150
TUNER, CD, AUX, TAPE, MD:
7 Hz to 100 kHz
+0 dB
PHONO:
20 Hz to 20 kHz ±3 dB
PHONO MC: 0.18 mV, 100 ohms
MM: 1.6 mV, 50 kilohms
TUNER, CD, AUX, TAPE, MD:
150 mV, 20 kilohms
PHONO MC: 75 dB (A Fil, 0.5 mV)
MM: 85 dB (A Fil, 5 mV)
TUNER, CD, AUX, TAPE, MD: 100 dB
(input short)
MD REC OUT, TAPE REC OUT:
150 mV, 1 kilohm
PRE OUT: 600 mV, 200 ohms
Corresponding to Low/High
impedance headphones: 10 mW (8
ohms)
BASS (100 Hz): ±6 dB
TREBLE (10 kHz): ±6 dB
220 - 230 V AC, 50/60 Hz
100 W
280 x 100 x 400 mm
(11 x 3
15 /
16
x 15 3 /
4
inches)
incl. projecting parts and controls
7.0 kg (15 lb 7 oz)
Shorting plug* (2)
Mains lead (1)
* plugged into the PHONO jacks
when shipped from the factory
–3
Outputs
Inputs
General
Supplied accessories
Design and specifications are subject to change without
notice.