KORG AX10A - Manual (Page 5)

6
Parts and what they do
Front panel
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
1 Display
Indicates the program number. When you operate a
knob, selector or button, or move the pedal when the
pedal FX is set to Notch, the parameter value will
briefly appear in the display.
• This will light when the power is on.
• The dot in the lower right of the display will light
when you edit a parameter value.
• If the AX10A is running on batteries, will blink
when the batteries run low.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2 NOTCH selector
Adjusts the frequency of the notch filter. You can
suppress acoustic feedback by using the notch filter to
cut the frequency region at which feedback is occurring.
3 Tone control knobs
These knobs adjust the overall tone and volume of
the AX10A.
By turning the LEVEL/NR knob while you hold down
the FUNCTION button, you can adjust the amount of
noise reduction (NR).
Some settings may cause distortion in your sound.
If this occurs, adjust the tone control LEVEL/NR
knob (or the MASTER buttons).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
4 PRE FX (TUNER) LED
These indicate the selected pre-effect.
The LEDs will not light if the pre-effect is off.
When the tuner is operating, these LEDs indicate the
difference from the correct pitch. (p.9)
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5 PRE FX button
Each time you press this button, the pre-effect type
will change in the order of COMP
→ LIMITER →
EXCITER
→
COMP etc.
6 VALUE (CALIB) buttons –ON/OFF–
These buttons adjust the value of the pre-effect.
You can switch PRE FX on/off by pressing the
VALUE
▲
and
▼
buttons simultaneously.
When the tuner is operating, you can use these
buttons to adjust the calibration (CALIB).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
7 MIC & BODY selector
Selects one of eleven types of mic or body modeling.
8 DEPTH (VOL PEDAL MIN) buttons -ON/OFF-
These buttons adjust the depth of the mic or body
modeling effect (DEPTH).
If you’ve assigned the expression pedal to control
Volume, you can set the minimum volume when the
pedal is fully returned (i.e., toward yourself) by
holding down the FUNCTION button and pressing
▲
or
▼
(VOL PEDAL MIN).
You can switch the MIC & BODY effect on/off by
pressing the DEPTH
▲
and
▼
buttons together.
When off, the MIC & BODY LED will not be lit.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
9 AMBIENCE selector
This selects one of 11 ambience effects.
10 AMB/CHORUS buttons -ON/OFF-
These buttons adjust the depth of the ambience effect.
You can adjust the depth of the chorus by holding
down the FUNCTION button and pressing these
buttons.
You can simultaneously switch the ambience effect
and chorus effect on/off by pressing the AMB
▲
and
▼ buttons together.
1 3
4
5
6
2
7
8
9
10
12
13
14
11
16
17
18
19
15