KORG AX10A - Manual (Page 6)

7
TIPS If you want to turn off either the ambience effect or
the chorus effect, use the AMB (CHORUS)
▼
button to set its value to “00”.
11 TAP button
You can set the delay or reverb time of the ambience
effect by tapping this button at the desired interval. The
LED located at the left will blink to indicate the tempo.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
12 FUNCTION button
By holding down this button and operating a knob or
button that has a function printed in green on the
front panel, you can edit the parameter printed in
green.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
13 MASTER (CANCEL) buttons
These buttons adjust the overall volume of the
AX10A (MASTER).
When the AX10A is ready to write (store), pressing
either of these buttons will cancel the Write operation
(CANCEL).
14 WRITE button
Use this button to write (store) a program.
When you press this button, the AX10A will enter
“write-ready” mode; if you press this button again, the
program will be written (stored). (p.12)
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
15 PEDAL FX/BANK HOLD button
This button selects the effect that will be controlled
by the expression pedal (Pedal Effect).
Each time you press the button, the LED will change
color to indicate the pedal effect that will be controlled.
ORG: NOTCH (orange): Notch filter frequency
RED : CHO (red): Chorus effect
GRN : AMB (green): Effect selected by AMBIENCE
OFF : VOLUME (dark): Volume pedal
By holding down the FUNCTION button and pressing
this button, you can select “bank hold” mode as the
way in which programs will be selected (BANK
HOLD). Refer to “Selecting programs: b” (p.9).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
16 Expression pedal
You can use this expression pedal to control effects or
volume. By advancing the pedal all the way forward
you can switch the selected pedal effect on/off.
VOLUME and NOTCH cannot be switched on/off by
advancing the pedal.
17 PEDAL LED
This LED will light if the expression pedal is active.
18 ORIGINAL VALUE LED
This LED will light if the edited value is identical to
the saved (original) value.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
19 Program select switches DOWN/BANK DOWN, UP/
BANK UP –BYPASS, TUNE–
Use these switches to select programs. You can
select programs in one of three ways. Refer to
“Selecting programs” (p.9).
If you press the UP and DOWN switches simulta-
neously, the effects will be bypassed and the tuner
will operate (BYPASS) (p.9).
Rear panel
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
20 INPUT L/H select switch
Set this switch according to the pickup output of your
guitar.
H : Suitable for guitars with a high output pickup
L : Suitable for guitars with a low output pickup
21 INPUT jack
Connect your guitar to this jack. Use a 1/4" mono
plug. If the AX10A is running on batteries, the power
will come on when you plug into this jack.
If the AX10A is running on batteries, the power will
not come on if a 1/4" stereo plug is inserted.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
22 OUTPUT jack
Connect this jack to your guitar amp, recorder, or
headphones.
24 25 20 21 22 23
23 AMP/LINE select switch
Set this to “AMP” if you’re plugging in to a PA system
or guitar amp for use at high volume. Set this to
“LINE” if you’re plugging in to a recorder or head-
phones etc.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
24 DC9V
The separately sold AC adapter can be connected
here (p.8). When this is connected, the power will be
turned on automatically.
You must only use the specified AC adaptor (p.14).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
25 Cable hook
If the separately sold AC adapter is used, connect
the cable of the AC adapter around this hook (p.8).