P.39), Using 10’s hold to select programs, Using a footswitch to select pro- grams – KORG X50 User Manual
Page 45: Midi channel setting
Selecting programs
39
Quick Star
t
In
tr
oduc
tion
S
etup
Pro
g
ra
m
C
ombina
tion
Multi
Effec
t
Global
Ar
peggia
tor
Drum Kit
Ex
ternal c
on
tr
ol
O
ther func
tions
Ap
pendic
es
3.
Use the ClickPoint to select “Program Select.”
Use the [INC][DEC] buttons or the [VALUE]
dial to consecutively step through programs in
the same category.
4.
To exit the Category Hold function, press the
[./HOLD] button twice to erase the “Cat.
HOLD” display.
Note: In PROG 0: Play, pressing the [./HOLD]
button will cycle through “Cat. HOLD”
→ “10’s
HOLD”
→ cancel.
Using 10’s HOLD to select programs
You can fix the ten’s place of the program number
as you select programs.
1.
Choose “Program Select.”
2.
Press the [./HOLD] button to make the display
indicate “10’s HOLD.”
The ten’s place of the program number will be
held (fixed).
3.
By pressing a numeric button [0]–[9], you can
input the one’s place in a single action.
4.
You can use the [INC][DEC] buttons to change
the ten’s place.
5.
To cancel the 10’s HOLD function, press [./
HOLD] to erase the “10’s HOLD” display.
Using a footswitch to select Pro-
grams
You can assign a footswitch to step through Pro-
grams one by one, either going up (0, 1, 2, 3, etc.)
or going down (3, 2, 1 etc.).
This lets you change Programs without using your
hands–great for quick Program changes in live
performance situations.
To set this up:
1.
Connect a foot switch to the rear-panel
ASSIGNABLE SWITCH jack.
Use a simple on/off footswitch, such as the
optional KORG PS-1.
2.
Press the [GLOBAL] button to enter Global
mode.
3.
Press the [EXIT] button to access the GLOBAL
0: System page.
4.
Press the [PAGE+] button to access the Foot tab.
5.
Select “Foot SW Assign,” and specify either
Program Up or Program Down.
Program Up
lets you select the next higher
program number each time you press the foot
switch.
Program Down
lets you select the next lower
program number each time you press the foot
switch.
6.
Set the “Foot SW Polarity” to the polarity of the
pedal you’ve connected.
If you’ve connected a separately sold PS-1
pedal switch, choose the (–) KORG Standard
setting.
With these settings, you will step through the
programs one at a time each time you press the
foot switch.
If you want this setting to be remembered even
after you turn off the power, be sure to write
the changes you made. (
7.
Use the [PROG] button to enter PROG 0: Play,
and press the foot switch; the program will
change.
Note: This setting applies to selecting Combinations,
as well.
Using MIDI program change mes-
sages to select programs
By sending MIDI program change messages along
with MIDI bank select messages to the X50 from
an external MIDI device (a MIDI sequencer such
as a DAW program, or a MIDI controller, etc.), you
can select any program in the six banks.
You can also install the included “X50 Plug-In Edi-
tor” into your DAW program as a plug-in, and
easily select X50 programs or combinations from a
list within your DAW. For more details, see “Edi-
tor/Plug-In Editor Manual” (PDF).
MIDI channel setting
In order to play the X50 via MIDI, the transmitting
device (MIDI sequencer or computer) and receiv-
ing device (the X50) must be set to the matching
MIDI channel. In Program mode, the X50 receives
data on the global MIDI channel.
1.
Make sure that the X50 and your external MIDI
device or computer are connected correctly.