Kenwood VRS-6100 - Manual (Page 18)

18 EN
Preparing for playback
SETUP
POWER ON/STANDBY MULTI CONTROL @/#
SETUP
MULTI
CONTROL
%/fi
POWER
Speaker settings
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back speakers) as described below.
1
Turn on the power to this receiver by pressing the POWER
ON/STANDBY key (or POWER key).
2
If you want to use the remote control unit, press the RECEIVER
key on the remote to set it to the receiver control mode.
3
Initiate the setup mode.
1 Press the SETUP key.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) for the following displays.
1 "SP SETUP"
2 "TEST TONE"
3 "DISTANCE"
4 "LFE LEVEL"
5 "EXIT"
÷ While the main setup display is appeared, the setup mode
can be canceled by selecting "EXIT" and then pressing the
SETUP key.
The flow of the SETUP is as follows;
SP SETUP TEST TONE DISTANCE EXIT LFE LEVEL
Front Left
Center
Front Right
Right Surround
HTB 1
HTB 2
HTB 3
Custom
Subwoofer
Front
Center
Surround
Surround
Back
MANUAL AUTO
L
C
R
RS
LS
RB
LB
SW
L
C
R
RS
RB
LB
LS
SW
Subwoofer
Re-mix
Left Surround
Surround Back Left
Surround Back Right
4
Select a speaker system.
1 Select "SP SETUP" and press the SETUP key again so
that the speaker system indication "SP SYSTEM"
scrolls across the display.
s P Y s s T E M
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the speaker system
setting.
1 "HTB 1": Select "HTB 1" if you use speaker system KS-2100HT.
2 "HTB 2": Select "HTB 2" if you use speaker system KS-708HT.
3 "HTB 3": Select "HTB 3" if you use speaker system KS-908HT.
4 "CUSTOM": Select to set up the speakers according to
the speaker system in use. (Speaker setup is required
every time after the speaker system is changed.)
÷ When the setting "HTB 1", "HTB 2" or "HTB 3" is selected, the
procedure skips to step 5.
÷ When you use a KENWOOD speaker system and select
"HTB 1", "HTB 2" or "HTB 3" set the speaker setup, the audio
will be corrected automatically according to the speaker
characteristics.
÷ When the speaker setting is set to "HTB 1", "HTB 2", "HTB 3 " or
"BS OFF" the DOLBY PRO LOGIC IIx, DTS-ES and DOLBY
DIGITAL EX listen modes cannot be selected.
3 For general speaker setting, use the MULTI CONTROL
button (or the MULTI CONTROL %/fi keys) to select
"CUSTOM", and press the SETUP key again.
÷ The subwoofer setting indication "SUBW" appears.
sU B W 0 N
4 Use the MULTI CONTROL button (or the MULTI CON-
TROL %/fi keys) to select the appropriate subwoofer
setting.
1 SUBW ON
When a subwoofer is connected.
2 SUBW OFF
When no subwoofer is connected.
÷ The initial setting is "SUBW ON".
÷ When "SUBW OFF" is selected and the selection is
established by pressing SETUP key in step 5 below,
the front speakers are set automatically to "FRNT LRG"
and the procedure jumps to step 8.
5 Press the SETUP key to accept the setting.
÷ The front speakers setting indication "FRNT" appears.
FR N T L R G
Continued to next page
*5484/16-27/EN 04.5.17, 8:34 AM 18