KORG Electribe EM-1 - Manual (Page 37)

4.Pattern mode
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
4.P
atter
n mode
37
Copying a part (Copy Part)
You can copy the sound settings and pattern data (including
motion sequence) from a selected part to another part.
1. If the pattern is playing, press the Stop/Cancel key to stop
playback.
2. Press the Part key to select the copy destination part (the
LED will light).
3. Hold down the Shift key and press step key 6 (Copy Part).
(Key 6 will blink.) The display will begin blinking.
4. Rotate the dial to select the copy source pattern number.
5. Press a part key to select the copy source part. (The copy
source key will blink, and the copy destination key will be
dark.) At this time, you will be able to audition the sound
each time you press the copy source part key. (Synth parts
will sound at C4.)
6. Press step key 6 once again to execute the Copy Part opera-
tion.
To cancel, press the Stop/Cancel key.
When copying between a synth part and a drum part,
only the trigger data will be copied.
For details on data copy within the same part, refer to
the following section "Data Copy within a part."
2
3
3,6
4
5
C.20
Synth part 1
Synth part 2
Drum part 1
A.01
d.01
Example
Synth part 1 (copy of C.20 Synth part 2)
Synth part 1 (sound, phrase pattern)
Copy destination
Copy source
Synth part 2 (sound, phrase pattern)
Drum part 1 (sound, rhythm pattern)
Synth part 2 (copy of A.01 Synth part 1)
Drum part 1 (sound, rhythm pattern)
Data Copy within a pattern
Phrase pattern data (including motion sequence data) that you
create for a pattern of length 1 can be copied to the steps of
lengths 2...4. This function is a convenient way to create a pat-
tern that uses similar phrases repeatedly.
1. Create a pattern with a length of 1, and Write it into memory.
(Refer to p.41 "Saving a pattern.")
2. At this point, the same data as in length 1 will automatically
be copied to the steps of lengths 2...4.
3. Change the pattern length to the desired length. (Refer to
p.31, "Length, Scale/Beat settings.")
4. The steps of lengths 2...4 will contain the same data as length
1. Now you can edit the data of lengths 2...4 to complete the
pattern.
The data will be copied in a similar way when the pattern
length is 2 or 3 (refer to the table below). If you shorten a pat-
tern you create, the data will be copied according to the short-
ened length.
Pattern data
after writing
A С С С A A A A
A B С С A B A B
A B C Ñ A B C C
Pattern data before
writing Pattern
length
1
2
3
Copy Pattern data
The data that is copied automatically when you Write a
pattern does not force the pattern length (1...4) to change.
If the length is 4, data will not be copied within the pat-
tern.
Copying the sound of a part
(Copy Sound)
You can copy the sound of another part to the selected part.
(Step data and motion sequence data will not be included.)
1. If the pattern is playing, press the Stop/Cancel key to stop
playback.
2. Press a part key to select the copy destination part. (The key
will light.)
3. Hold down the Shift key and press step key 7 (Copy Sound)
(key 7 will light). The display will begin blinking.
4. Use the dial to select the copy source pattern number.
5. Press a part key to select the copy source part. (The copy
source key will blink, and the copy destination key will be
dark.) At this time, you can audition the sound by pressing
the copy source key. (Synth parts will sound at C4.)
6. Press step key 7 once again to execute the Copy Sound op-
eration.
To cancel, press the Stop/Cancel key.
It is not possible to copy sounds between a synth part
and a drum part.