Kenwood TS-570D - Manual (Page 55)

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
49
12 OPERATOR CONVENIENCES
Consult the following table to select a function.
Selecting OFF assigns no function to the button.
1 Press [MENU].
2 Press [A/B] to select Menu A or Menu B.
3 Turn the MULTI/CH control to select Menu No. 41,
42, 43, 44, or 45.
4 Press [UP], [DOWN], Mic [UP], or Mic [DWN] to
select a function number.
• Consult the above table to select a function.
5 Press [MENU] to exit Menu mode.
The default values are as follows:
• Front panel [PF]: Voice 1
• Mic [PF1]: [A/B] • Mic [PF2]: [SPLIT]
• Mic [PF3]: [M/V] • Mic [PF4]: Monitor
Note:
◆ Full Reset returns the functions of the PF buttons to default
settings.
◆ Function No. 84 accessible in step 4 is not currently available.
Pressing the PF button with Function No. 84 assigned will
simply cause the transceiver to display a string of error codes.
BEEP FUNCTION
The purpose of the Beep function is to provide an audible
signal that conveys information. There are three types of
signals:
• To confirm that a button has been pressed.
• To report an error condition; Morse codes are used for
some errors.
• To confirm that the selection was completed by
pressing [MIC], [PWR], [KEY], [DELAY], or [FILTER]
again.
When selecting an operating mode, a Morse code
abbreviation for that mode is heard.
You can change the volume of the beep output via Menu
No. 01.
DISPLAY DIMMER
The Display illumination can be switched between 5 levels
via Menu No. 00.
PROGRAM FUNCTION BUTTON
The transceiver allows you to customize the function of the
front panel [PF] button. When using the optional MC-47
microphone, you can also customize the functions of the
Mic [PF1], [PF2], [PF3], and [PF4] buttons. You can
assign the following types of functions to these buttons via
Menu No. 41 to 45:
• Directly select Menu No. 00 to 40, 48 to 51. No need to
press [MENU] and turn the MULTI/CH control.
• Activate a function that is supported by no other front
panel buttons.
• Activate the same function as one of the front panel
buttons.
LSB
USB
CW
CW –R
FSK
FSK –R
AM
FM
· – · · (L)
· · – (U)
– · – · (C)
– · – · · – · (CR)
· – · (R)
· – · · – · (RR)
· – (A)
· · – · (F)
Morse Code Output Mode
67
68
69
70
71
72
73
74
75
76
00 to 40
80 to 83
Function
Number
Function
Function
Number
Function
[SCAN]
[M>VFO]
[M.IN]
[CW TUNE]
[CH 1]
[CH 2]
[CH 3]
[FINE]
[F. LOCK]
[CLR]
Selects Menu
No. 00 to 40.
See “MENU
CONFIGURATION”.
50
51
52
53
60
61
62
63
64
Monitor
Voice 1
Voice 2
DSP Filter
Monitor
QUICK
MEMO [MR]
QUICK
MEMO [M.IN]
[SPLIT]
[TF-SET]
[A/B]
65 [M/V]
66 [A=B] OFF 99
Selects
Menu No.
48 to 51.
Ex: 82
selects
Menu No.
50.